manualshive.com logo in svg

YOKOGAWA ScopeCorder DL950, User Manual

Share
Download
YOKOGAWA ScopeCorder DL950 User Manual Download Page 258

19-12

IM DL950-02EN

Selecting the Waveform Save Range (Range)

3.

 Tap 

Range

, or press the soft key.

 

When dual capture is on, tap 

Low Speed Save Range

 or 

High Speed Save Range

, or press 

the soft key. The following screen appears.

Scope Mode

  

Saves the data displayed in the main 

window

Saves the range of data displayed in 

the zoom window Zoom1

Saves the range of data displayed 

in the zoom window Zoom2
Saves the data in the area between 

the cursors

When Dual Capture Mode Is Off

When Dual Capture Mode Is On

Low-speed sampling

High-speed sampling

Saves the data displayed 

in the main window

Saves the range of data 

displayed in the zoom window

Recorder Mode

  

Saves the data of the entire measured waveforms

Saves the data displayed in the main window

Saves the range of data displayed in the zoom 

window
Saves the data in the area between the 

cursors

19.4  Saving Waveform Data

Summary of Contents for ScopeCorder DL950





























































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands