YOKOGAWA ScopeCorder DL950 User Manual Download Page 177

Page: 177 / 316

11-9

IM DL950-02EN

Displaying the Measured Results (Display Result)

Tap

Display Result

, or press the soft key. The following screen appears.

When this scroll bar is displayed, you can drag the screen or

use the left and right arrow keys to scroll the display.

↑: Displayed next to the maximum value of each measurement item.

↓: Displayed next to the minimum value of each measurement item.

Sorts the display

(Forward, Reverse)

Displays the

maximum value

Displays the

minimum value

11.3 Performing Cyclic Statistical Processing

Summary of Contents for ScopeCorder DL950





























































































































































































































































































































Search results

Summary of Contents for ScopeCorder DL950

Reviews:

Related manuals for ScopeCorder DL950

Brands by name

Popular brands

YOKOGAWA ScopeCorder DL950, User Manual

Search results

Summary of Contents for ScopeCorder DL950

Reviews:

Related manuals for ScopeCorder DL950

Brands by name

Popular brands