manualshive.com logo in svg

YOKOGAWA ScopeCorder DL950, User Manual

Share
Download
YOKOGAWA ScopeCorder DL950 User Manual Download Page 154

9-2

IM DL950-02EN

9.1  Displaying Waveform History Waveforms

This section explains the following settings for displaying history waveforms, which are waveforms 
that were previously saved to acquisition memory:

Applicable to Scope Mode

•  Display mode
•  Highlighting the selected record number
•  Display range (start and end record numbers)
•  Showing a list of timestamps
•  Clearing all history waveforms

► “History Waveform Display/Search (Scope mode only)” in the Features Guide

HISTORY menu

1.

  On the waveform screen’s MENU, tap 

ANALYSIS

 > 

HISTORY

, or press 

HISTORY 

(ANALYSIS)

.

  

* This setting only appears when Display Mode is set to 1 Record or All Record.

See “Setting the Display Mode.”

Set the highlight display.*

Set the display range.

See “Displaying a List of History 

Waveforms.”

Deletes all the history waveforms

(Changes to Execute when Search Mode is not 

set to OFF (see section 9.2)).

Search history waveforms 

► sec. 9.2

In dual capture mode

Setting the Display Mode (Display Mode)

2.

 Tap 

Display Mode

, or press the soft key.

 

From the menu that appears, select the display mode.

 

1 Record:  Only the waveform corresponding to the selected record number is displayed.

1

 

All Record:   All selected waveforms are superimposed on each other.

2

 

 

 

All other waveforms

1

 are displayed with an intermediate color.

 

Average Record: 

 Computes the linear average of all the selected waveforms

2

 and displays 

the result.

  1  Specify the highlighted waveform with Selected Record.

  2  Specify with Start Record and End Record.

Summary of Contents for ScopeCorder DL950





























































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands