manualshive.com logo in svg

YOKOGAWA ScopeCorder DL950, User Manual

Share
Download
YOKOGAWA ScopeCorder DL950 User Manual Download Page 146

8-2

IM DL950-02EN

8.1  Searching for Edges

This section explains the following settings for searching for edges:

Items Common to Scope Mode and Recorder Mode

•  Search type
•  Search conditions (source waveform, level for determining the state of the source waveform, 

edge polarity, hysteresis, and the number of times to detect the conditions)

•  Detected waveform display window (Scope mode)
•  Detected point number
•  Search range
•  Executing searches

► “Edge Search (Edge)” in the Features Guide

SEARCH Edge Menu

1.

  On the waveform screen’s MENU, tap 

ANALYSIS

 > 

SEARCH

, or press 

SHIFT+ZOOM 

(SEARCH)

.

2.

  Set Type to 

Edge

.

  

See “Executing a Search.”

Set the search end point.

Set the search start point.

See “Configuring the Search Result Display 

Window (Zoom Window).”

See “Setting Search Conditions.”

Set the search type to Edge.

Displays detected waveforms 

(See “Executing a Search.”)

Summary of Contents for ScopeCorder DL950





























































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands