manualshive.com logo in svg

YOKOGAWA ScopeCorder DL950, User Manual

Share
Download
YOKOGAWA ScopeCorder DL950 User Manual Download Page 142

7-6

IM DL950-02EN

7.2  Zooming In on or Out of Waveforms (Recorder 

mode)

This section explains the following settings for zooming in or out of waveforms in Recorder mode:

Applicable in Recorder Mode

•  Turning zoom on and off
•  Zoom position
•  Display range (zoom factor)
•  Display format
•  Main window’s display ratio
•  Window layout
•  Auto scroll
•  Zoom source waveform
•  Changing the range for performing automated measurement of waveform parameters

► “Zooming in on or Out of Waveforms” in the Features Guide

ZOOM Menu

1.

  On the waveform screen’s MENU, tap 

ANALYSIS

 > 

ZOOM

, or press 

ZOOM

. The ZOOM 

menu appears.

  

See “Switching between 

the Main Window and 

Zoom Window.”

ZOOM menu (page 1/2)

Set the main window’s display 

ratio (50%, 20%, 0%).

Set the window layout 

(Side, Vertical).

See “Setting Auto 

Scrolling.”

See “Allocating Zoom Source 

Waveforms.”

Displays the first 

page of the menu

Set the range of automated 

measurement of waveform 

parameters to the zoom area.

ZOOM menu (page 2/2)

Summary of Contents for ScopeCorder DL950





























































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands