manualshive.com logo in svg

YOKOGAWA ScopeCorder DL750, User Manual

Share
Download
YOKOGAWA ScopeCorder DL750 User Manual Download Page 276

18-5

IM 701210-06E

Troubleshooting, Maintenance, and Inspection

18

18.2 Messages and Corrective Actions

Code

Message and Corrective Action

Section

780

Firmware was not overwritten in the following slots, since the version of the firmware in the module

–

and that of the replacement firmware were the same. Check the versions on the overview screen.
SLOT: XX

781

Cannot start while the following setup menus are displayed.

–

Press the ESC key to clear the menu, and then start.
(ALL CH, ZOOM, MEASURE, CURSOR, PrintSetup)

782

Firmware was not overwritten, since the version of the firmware in the printer and that of the

18.4

replacement firmware were the same.

783

Checksum error in the printer control program.

3.4

Recycle the power.  If the error occurs again, maintenance service is required.

784

Failed to transmit the printer control program.

3.4

Recycle the power.  If the error occurs again, maintenance service is required.

785

Failed to write the printer control program.

3.4

Recycle the power.  If the error occurs again, maintenance service is required.

786

Cannot perform numeric recording when the floppy disk drive is specified.

13.7

Select another drive with FileList and execute it again.

787

Cannot be carried out during recording.

7.1

Press the START/STOP key to stop the waveform acquisition first.

788

Cannot start while the alert dialog box is open.

–

Press the ESC key to clear the dialog box, and then start.

789

Cannot copy if 100 pages is exceeded.

9.8, 12.2

Change the multiplier or range.

790

Fine Print or Zoom Print is not possible when X-Y display is present.

8.6, 12.2

Errors in Setting (800 to 899)

Code

Message and Corrective Action

Section

800

Illegal date-time.  Set the correct date and time.

3.5

801

Illegal file name. The file name contains characters which are not allowed or the file name is not a

Chapter 13

valid MS-DOS file name.  Enter another file name.

803

Turn off accumulate mode to enter history menu. It is not possible to activate the history menu by

8.4

pressing the HISTORY key during accumulation.

804

Cannot change this parameter while running.  Press the START/STOP key to stop acquisition.

7.1

806

Cannot change settings during GO/NO-GO.  Stop the GO/NO-GO.

11.8, 11.9

808

Can not change display points with this T/div setting.

5.2

809

Cannot change edge for status other than X.

Chapter 6

Set the state of the channel corresponding to condition A to ‘X’.

811

Cannot change display points in roll mode.

5.2

813

Set Items in measure menu.  Set appropriate measurement items.

11.6

814

Duplicated Name.  Change the label string.

8.10

816

Cannot turn off with the current record length.  Please Change record length.

7.2

817

Cannot change.  Please change X Trace in the X-Y menu.

8.6

818

Cannot change when GO/NO-GO Mode is Zone.

11.9

819

Cannot change when Channel Display is OFF or Math settings are invalid.

5.1,

Set the channel display ON or make appropriate Math settings.

Chapter 10

821

Cannot change when External Clock is active.

5.14

823

Cannot change while running.

7.1

824

Cannot change with the current acq mode.  Set the acquisition mode to Normal.

7.3

827

Illegal math expression.  Input a correct computing equation.

10.5

829

Cannot change when Logic Mode is OFF or all bits of Logic Display are OFF.

5.20

830

Cannot set anything other than Low Pass for a Gaussian filter.

10.5

Change the Filter Type to another filter besides Gaussian.

834

Duplicate SCSI ID.  Set different ID numbers.

13.6

835

Cannot change settings while realtime printing or realtime recording.

11.2

Stop printing or recording.

Summary of Contents for ScopeCorder DL750























































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands