Home
/
YOKOGAWA
/
ScopeCorder DL750
/
User Manual

YOKOGAWA ScopeCorder DL750, User Manual

Share

Page: 172 / 406

YOKOGAWA ScopeCorder DL750 User Manual Download Page 172

13-59

IM 701210-06E

Saving and Loading Data

13

Property

Displays the following information about the selected file: filename.extension, the file

size, the date the file was saved, the attribute, etc.

Note

•

Files cannot be deleted while the data acquisition is in progress.

•

Data that is deleted cannot be recovered. Make sure you erase the correct files.

•

You can not delete directories if there are files in them.

•

If an error occurs while deleting multiple files, the files after the error occurrence are not
deleted.

•

You cannot change a directory attribute.

•

This function cannot be used when using the FTP server function, network printer function,
or the Web server function.

•

The screen image data and thumbnail data are saved in pairs of files. If you specify “*.*”
for the files to be displayed (Filter) on the File List and manipulate individual files (Delete,
Rename, or Copy), the thumbnail display function can no longer be used.

•

If the realtime recorded waveform is being displayed, the file cannot be deleted.

•

If you wish to delete the files on the [RealTime] drive, set Data Type to Real Time.

13.15 Changing the File Attributes and Deleting Files

«
...
170
171
172
173
174
...
»

Summary of Contents for ScopeCorder DL750























































































































































































































































































































































































































Reviews:

No comments

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands