manualshive.com logo in svg

YOKOGAWA PX8000, User Manual

Share
Download
YOKOGAWA PX8000 User Manual Download Page 14

1-1

IM PX8000-02EN

1.1  Configuring Wiring System Settings

This section explains the following wiring system settings.
•  Wiring system
•  Efficiency equation
•  Turning independent element configuration on and off
•  Delta computation
•  Display format of external current sensor range
•  Deskewing (correcting the transfer time difference between input signals)

►

 Features Guide: “Wiring System Settings (WIRING)” 

WIRING Menu

Press 

WIRING

 to display the following menu.

 

Set the display format of external current sensor range 

(Direct, Measure).

Turns independent element configuration on and off

Set delta computation.

Set the efficiency equation.

Set deskewing.

Set the wiring system.

Setting the Wiring System

Press the 

Wiring

 soft key to display the following screen.

 

Set the wiring system (1P2W, 1P3W, 3P3W, 3P4W, 3P3W(3V3A)).

When you select an element, the wiring systems that you can select are displayed. Select the wiring system 

from those displayed.

Wiring System Combination

•   If you select 1P3W, 3P3W, 3P4W, or 3P3W(3V3A) for the wiring system, the wiring unit is set with the two 

or three elements adjacent to the selected element whose element numbers are larger than the selected 

element.

•   On models that have four elements installed, up to two wiring units (ΣA and ΣB) are automatically set. The 

wiring unit symbols ΣA and ΣB are attached to the element numbers in order, starting with the smallest 

number.

Note

•  Because the wiring system with the largest element number is automatically determined according to 

the settings of the wiring system with the smallest element number, the element with the largest element 
number cannot be selected.

•  You cannot set the wiring units for larger element numbers before the wiring units for smaller element 

numbers.

Chapter 1 

Fundamental Measurement Conditions

Summary of Contents for PX8000











































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands