manualshive.com logo in svg

YOKOGAWA PX8000, User Manual

Share
Download
YOKOGAWA PX8000 User Manual Download Page 117

15-2

IM PX8000-02EN

15.2  Performing Binary Conversion

This section explains the following settings for performing binary conversions:
• Computation
  Function (Bin(S1)), computation source waveform, threshold level, unit, label, turning the waveform 

display on and off

• Scaling
•  Computation start and end points

►

 Features Guide: “Binary Conversion (Bin (S1))”

MATH Menu

Press 

MATH

 to display the following menu.

 

Set the computation.

Set the computation start and end points. ► section 15.1

Set Mode to ON.

Set the scaling. ► section 15.1

Configuring Computations (Math Setup)

1.

 

Press the 

Math Setup

 soft key.

2.

 

Press a soft key from 

Math1

 to 

Math8

 to display the following screen.

 

  

Selection function Bin(S1).
Select the computation source waveform

(U1-U4, I1-I4, P1-P4, AUX3-AUX8, Math1-Math7).
Set the upper and lower limits of the threshold.

(Within ±5 div of the computation source waveform)

Turns the waveform display on and off

Set the label.

Set the unit.

Summary of Contents for PX8000











































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands