manualshive.com logo in svg

YOKOGAWA IR202, User Manual

Share
Download
YOKOGAWA IR202 User Manual Download Page 8

 

 

<1.  GENERAL>

1-1

IM 11G02Q02-01EN 2nd Edition : Sep. 04, 2020-00

1.  GENERAL

This product provides a communication function through RS-485 interface, which allows data 

transmit to or receive from the host computer and other devices.
The communication system is comprised of a master station and slave stations. Up to 31 of slave 

station (present instrument) can be connected per master station (host computer, programmable 

controller, graphic display panel, etc.) through RS-485 interface.
Because the master station can communicate with only one slave station at a time, the 

destination can be identified by the “Station No” set for each slave station.

In order that the master station and the slave station can communicate, the format of the 

transmit/receive data must coincide. The format of the communication data is determined by the 

MODBUS protocol
[RS-232 <=> RS-485 converter] (recommended )
 

Type: 

KS-485 (non-isolated type)/SYSTEM SACOM Corp.

 

Type: 

SI-30FA (isolated type)/SEKISUI ELECTRONICS Co., Ltd.

[USB <=> RS-485 converter] (recommended article)
 

Type: 

USB-485I / SYSTEM SACOM Corp.

RS-485

USB

RS-485

RS-232C

RS-485

RS-485

Programmable controller

Converter

IR202

IR202

RS-232C or USB

Figure1.1 

Configuration between master and slave devices

Summary of Contents for IR202














































Reviews:

No comments

Brands by name

Popular brands

Load more brands