YOKOGAWA FLXA21 User Manual Download Page 40

Page: 40 / 64

<6. Function block parameters and Methods>

6-14

IM 12A01A02-72E

3rd Edition : Oct. 01, 2015-00

Table 6.2 Contents of Classic DIAGNOSIS

Octet Bit DIAGNOSIS Mnemonic

Description

Remarks

0 DIA_HW_ELECTR

Hardware failure of the electronic

Refer to Table of Device

status.

1 DIA_HW_MECH

Hardware failure mechanics

Refer to Table of Device

status.

2 DIA_TEMP_MOTOR *2

Motor- temperature too high

3 DIA_TEMP_ELECTR *2 Electronic temperature too high

4 DIA_MEM_CHKSUM

Memory error

Refer to Table of Device

status.

5 DIA_MEASUREMENT *2 Failure in measurement

—

6 DIA_NOT_INIT *2

Device not initialized (No self calibration)

—

7 DIA_INIT_ERR *2

Self calibration failed

—

0 DIA_ZERO_ERR

Zero point error (limit position)

Refer to Table of Device

status.

1 DIA_SUPPLY *2

Power supply failed (electrical,

pneumatic)

—

2 DIA_CONF_INVAL *2

Configuration not valid

—

3 DIA_WARMSTART *1

New start-up (warm startup) carried out. Should be set after power-on

or after FACTORY_RESET =

2506 has been executed.

4 DIA_COLDSTART *1

Restart (cold startup) carried out.

Should be set after

FACTORY_RESET = 1 has

been executed.

5 DIA_MAINTAINANCE *2 Maintenance required

—

6 DIA_CHARACT *2

Characterization invalid

—

7 IDENT_NUMBER_

VIOLATION *2

Set to 1 (one), if the IDENT_Number

of the running cyclic data transfer and

the value of Physical Block IDENT_

NUMBER_SELECTOR parameter do

not correspond. If IDENT_NUMBER_

SELECTOR = 127 (adaption mode) then

the DIAGNOSIS bit IDENT_NUMBER_

VIOLATION is cleared / not set.

—

0-7 Reserved *2

Reserved for use within the PNO

—

0-6 Reserved *2

Reserved for use within the PNO

—

7 EXTENSION_AVAILABLE More diagnosis information is available

—

*1:

This bit is Off 10 seconds after On.

*2:

Not available for FLXA21.

Device status

Device setting status and failures of FLXA21 are indicated by using parameter DEVICE_

STATUS_1, DEVICE_STATUS_2, DEVICE_STATUS_3, DEVICE_STATUS_4, DEVICE_

STATUS_5, DEVICE_STATUS_6, DEVICE_STATUS_7 and DEVICE_STATUS_8 (index 51, 52,

53, 54, 55, 56, 57 and 58) in Physical Block.

FLXA21-PH

DEVICE_STATUS_1: Table 6.3

DEVICE_STATUS_2: Table 6.4

DEVICE_STATUS_3: Table 6.5

DEVICE_STATUS_4: Table 6.6

DEVICE_STATUS_5: Table 6.7

DEVICE_STATUS_6: Table 6.8

DEVICE_STATUS_7: Not used.

DEVICE_STATUS_8: Table 6.9

Summary of Contents for FLXA21

































































Search results

Summary of Contents for FLXA21

Reviews:

Brands by name

Popular brands

YOKOGAWA FLXA21, User Manual

Search results

Summary of Contents for FLXA21

Reviews:

Brands by name

Popular brands