background image

IM 01C22T01-01E

2-16

2.  HART COMMUNICATOR OPERATION

(15) Burst Mode

The transmitter continuously sends the data stored in it
when the burst mode is set on. Either one of measured
pressure variable, % output value, or 4 to 20 mA
output value can be selected and sent. The data is sent
intermittently as a digital signal at 75 ms intervals
when the transmitter is set in the burst mode. There-
fore, communication by the HART simultaneous
communicator is also possible.

Setting of Burst Mode

F0234.EPS

Call up the Burst option, and set 
the data to be sent. 
• Pressure variable (PV)
• % output value (% range/current)
• 4 to 20 mA output value (Process 

vars/crnt)

EJA:
Burst option
********
 PV
 % range/current
 Process vars/crnt

HELP

DEL

ESC

ENTER

EJA:
Burst mode
Off
 On
 Off

DEL

DEL

ESC

ENTER

Call up the Burst mode and set to 
On.
Then, Press SEND (F2).

HELP

(ENTER)

(ENTER)

(SEND)

1. Device setup

4. Detailed setup

3. Output condition

4. HART output

3. Burst mode, 4. Burst option

To Release from the Burst Mode:

Call up the 

Burst mode

 display, and set to 

OFF

.

(16) Multidrop Mode

“Multidropping” 

transmitters refers to the connection

of several transmitters to a single communications
transmission line. Up to 15 transmitters can be con-
nected when set in the multidrop mode. To activate
multidrop communication, the transmitter address must
be changed to a number from 1 to 15. This change
deactivates the 4 to 20 mA analog output, sending it to
4 mA. The alarm current also is disabled.

Setting of Multidrop Mode

F0235.EPS

Call up the Poll addr and set the 
polling address. (a number from 1 to 
15)
And press SEND (F2) to send the 
data.

EJA:
Poll addr
  O
  0

HELP

DEL

ESC

ENTER

HART Communicator
Auto Poll
No
 No
 Yes

DEL

DEL

ESC

ENTER

Call up the Auto Poll and set to 
Yes.

HELP

(ENTER)

1. Device setup

4. Detailed Setup

3. Output condition

4. HART Output

1. Poll addr

Online

Utility

Auto Poll

NOTE

1. When the address is set and the multi-drop

mode is set to “No” at the same time, Online
menus cannot be called up and displayed. Be
sure to turn the multidrop mode to “Yes” after
setting the address with “Poll addr.”

2. When the same polling address is set for two

or more transmitters in multidrop mode,
communication with these transmitters is
disabled.

Summary of Contents for Dpharp vigilantplant EJA Series
































Reviews: