manualshive.com logo in svg

YOKOGAWA DL850 ScopeCorder, User Manual, Page: 71 / 190

Share
Download
YOKOGAWA DL850 ScopeCorder User Manual Download Page 71

3.11  Connecting an Acceleration Sensor

An acceleration sensor is connected when measuring acceleration on the 701275 (ACCL/VOLT). For a 

details on acceleration sensors, see the respective manuals.

 

WARNING

Over-Range Indication

If over-range is indicated, the DL850/DL850V may be receiving a voltage higher than the 

observed waveform or measured waveform values. To prevent electric shock, change the 

vertical scale with the SCALE knob so that the entire amplitude of the waveform is displayed 

within the waveform display area, and check the input voltage level.

 

     

Over-range indication

Indicates the number of the channel that over-range is occurring on.

Channel indication when over-range is occurring on multiple channels

Indicates the smallest number among the channels that over-range is 

occurring on.

 

CAUTION

•  Applying a voltage that exceeds the values indicated below to the 701275 (ACCL/VOLT) 

may damage the input section.

  Maximum input voltage: 42 V (DC + ACpeak)

•  When connecting acceleration sensors, do it without the bias current being supplied to the 

sensor. Otherwise, damage to the internal circuitry of the acceleration sensors may result.

•  The DL850/DL850V only supports acceleration sensors that are driven by constant current 

with driving current of 4 mA and driving voltage of 22 V.

Connecting Acceleration Sensors

When Connecting Built-in Amplifier Type Acceleration Sensors

The DL850/DL850V allows built-in amplifier type (low impedance) acceleration sensors to be directly 

connected. To connect built-in amplifier type acceleration sensors, use BNC cables. Use cables that 

are appropriate for the acceleration sensors being used.

Connect the acceleration sensors with the bias current turned off. After connection, turn on the supply 

current to the acceleration sensors for making measurements.

When Connecting Charge Output Type Acceleration Sensors

Since the charge output type (high impedance) acceleration sensors do not have built-in amplifier 

circuit, they cannot be directly connected to the DL850/DL850V. Use either of the following two 

methods to connect the sensors.

Using the Charge Amplifier

  Connect a charge-output-type acceleration sensor to the charge amplifier using a high-insulation, 

low-noise cable. The acceleration signal (charge signal) that has been converted to a voltage 

signal by the charge amplifier is input to the DL850/DL850V using a normal coaxial cable. The 

DL850/DL850V measures the signal in the voltage measurement mode. The measured data can be 

converted to acceleration values using the scale conversion function of the DL850/DL850V.

 

 

701275(ACCL/VOLT)

(voltage measurement)

Charge-output-type 

acceleration sensor

Normal coaxial 

cable

High-insulation, 

low-noise cable

Charge amp

DL850/DL850V

3-30

IM DL850-03EN

Summary of Contents for DL850 ScopeCorder































































































































































































Reviews:

No comments