YOKOGAWA DL850 ScopeCorder User Manual Download Page 104

Page: 104 / 190

5-4

IM DL850-03EN

5.4 Video Signal Output (VIDEO OUT (XGA))

CAUTION

• Only connect the DL850/DL850V to a monitor after turning both the DL850/DL850V and

the monitor off.

• Do not short the VIDEO OUT terminal or apply external voltage to it. Doing so may damage

the DL850/DL850V.

Video Signal Output Terminal

VIDEO OUT

(XGA)

You can use video signal output to display the DL850/DL850V screen on a monitor. Any multisync
monitor that supports XGA can be connected.

Item

Specifications

Connector type

D-sub 15-pin

Output format

Analog RGB output

Output resolution

XGA output, 1024 × 768 dots, approx. 60 Hz Vsync

D-Sub 15-pin receptacle

Pin No.

Signal

Specifications

Red

0.7 V

P-P

Green

0.7 V

P-P

Blue

0.7 V

P-P

—

GND

—

GND

—

Horizontal sync signal

Approx. 36.4 kHz, TTL positive logic

Vertical sync signal

Approx. 60 Hz, TTL positive logic

—

Connecting to a Monitor

Turn off the DL850/DL850V and the monitor.

Connect the DL850/DL850V and the monitor using an RGB cable.

Turn on the DL850/DL850V and the monitor.

Summary of Contents for DL850 ScopeCorder































































































































































































Search results

Summary of Contents for DL850 ScopeCorder

Reviews:

YOKOGAWA DL850 ScopeCorder, User Manual, Page: 104 / 190

Search results

Summary of Contents for DL850 ScopeCorder

Reviews: