YOKOGAWA DL7480 User Manual Download Page 87

Page: 87 / 176

2-32

IM 701450-51E

Selecting the Size of the Detail Analysis Results List (Display)

(firmware version 2.40 or later)

You can select whether to set the size of the display frame (Detail dialog box) of the

detailed analysis results list to full screen or half screen. If you select Half, the size of the

Detail dialog box decreases to half of its original size allowing you to view the zoom

waveform of the highlighted (selected) frame.

Zoom Ratio (Z1 Mag)

You can set the zoom ratio in the Z1 zoom box. The upper limit of the zoom ratio is

determined from the display record length as follows:

(Zoom ratio upper limit) = (Display record length)

50 (or 40)

The displayed record length does not necessarily match the set record length.

For details on the display record length, see appendix 1, “Relationship between the Time

Axis Setting, Sample Rate and Record Length” in the

DL7440/DL7480 User’s Manual

(IM701450-01E)

Zoom Position (Z1 Position)

The zoom position can be set by specifying the zoom center position (center of the Z1

zoom box) in the range –5 to +5 divisions with the center of the waveform display frame

set to 0 divisions. The resolution is as follows:

(Selectable steps of zoom position) = (T/div)

(display record length)

Setting the Search Condition: Search Setup

You can set the following conditions.

Search Type

You can select the search type.

Frame Pattern (Pattern Search)

Search the waveform by specifying a field or frame pattern.

Indefinite State (Indefinite Data Search)

Search indefinite data from the analysis data.

When Search Type Is Set to Frame Pattern

Search the waveform by specifying a field or frame pattern. If a waveform that matches

the pattern is found, the zoom box moves to that point and displays the specified

waveform.

If a pattern search is performed on data that contains indefinite data, the indefinite data

is considered both 1 and 0 (logical value) for the search. You cannot perform a pattern

search and an indefinite data search simultaneously.

When performing a pattern search, set the following items.

• Message Format

You can select a format for the Identifier (ID) field of the Arbitration field within the

data frame from the following:

Std

Standard format (11 bits)

Ext

Extended format (29 bits)

• Pattern Format

You can select a format for the Identifier (ID) field and the Data field from the

following:

Hex

Hexadecimal

Bin

Binary

2.5 Analyzing/Searching Data

Summary of Contents for DL7480

















































































































































































Search results

Summary of Contents for DL7480

Reviews:

Related manuals for DL7480

Brands by name

Popular brands

YOKOGAWA DL7480, User Manual

Search results

Summary of Contents for DL7480

Reviews:

Related manuals for DL7480

Brands by name

Popular brands