YOKOGAWA DL7480 User Manual Download Page 69

Page: 69 / 176

2-14

IM 701450-51E

• Standard Format and Extended Format of the Data Frame and Remote Frame

D
E

Recessive

Dominant

I R

DLC

(4 bits)

Arbitration Field

Data Field

Control

Field

Identifier (11 bits)

Standard Format

S
R
R

D
E

Recessive

Dominant

I R

DLC

(4 bits)

Arbitration Field

Data

Field

Control

Field

Identifier (11 bits)

Identifier (18 bits)

Extended Format

• Error Frame

Recessive

Dominant

Error Frame

Data Frame

Error Flag

(6 bits)

Superposition of Error Flags

(6 to 12 bits)

Error Delimiter
(8 bits)

Interframe Space or
Overload Frame

S: Trigger position for Start of Frame

Trigger position for Identifier

R: Trigger position for RTR

D: Trigger position for Data Frame

E: Trigger position for Error Frame

When Identifier Is Selected for the Frame/Field Type

• Condition

You can select from the following:

True

Trigger is activated when one bit pattern from ID1 to ID4 is met.

False

Trigger is activated when a bit pattern other than ID1 to ID4 is met.

• Bit Pattern: ID1 to ID4

You can set 4 types of bit patterns (ID1 to ID4).

When Pattern Format is set to Hex (hexadecimal), you can enter X, 0 to 9, or A to F in

units of 4 bits. When Pattern Format is set to Bin (binary), you can enter X, 0, or 1.

The trigger is activated on the OR condition of ID1 to ID4. The number of specified

bits varies depending on the message format type as follows:

Standard format (Std)

11 bits (the max value is 7FF when Pattern Format is set to Hex
(hexadecimal)).

Extended format Ext)

29 bits (the max value is 1FFFFFFF when Pattern Format is set to
Hex(hexadecimal)).

Note

•

If Identifier is selected (ON) and all the bits from ID1 to ID4 are set to X, the trigger does

not occur. The trigger does not occur even when combined with other field and frame

types in this condition.

•

When X is included in the ID1 to ID4 bit pattern, the trigger point is set to the end of the

Identifier (ID) in the same fashion as when 0, 1 is set to the bit pattern.

•

For ID1 to ID4 and Data Field bit patterns, if there is at least one “X” bit in a group of four

bits in the binary display, the corresponding hexadecimal display will show a “$.”

2.4 Setting CAN Bus Signal Acquisition Conditions

Summary of Contents for DL7480

















































































































































































Search results

Summary of Contents for DL7480

Reviews:

Related manuals for DL7480

Brands by name

Popular brands

YOKOGAWA DL7480, User Manual

Search results

Summary of Contents for DL7480

Reviews:

Related manuals for DL7480

Brands by name

Popular brands