YOKOGAWA DL7480 User Manual Download Page 38

Page: 38 / 176

1-33

IM 701450-51E

C Bus Signal Analysis Function

Detailed List of Analysis Data: Detail

More detailed information of the analysis data can be listed. The following information

can be displayed.

• Analysis number

• Stop condition/start condition

• Read/Write signal

• Time from the analysis reference point*

• Binary display of data

• Hexadecimal display of data

• Acknowledge bit condition

Stop condition

Start condition

Read/Write signal (R=Read, W=Write)

Time from the Reference Point*

Binary display of data

Hexadecimal display of data

Acknowledge bit condition

1: No acknowledge
0: Acknowledge present

Byte information immediately
before the stop condition

Byte information immediately
after the start condition

On the detailed display screen, the data corresponding to the specified number are

highlighted.

On the waveform display screen, the data corresponding to the specified number is

displayed in the ZOOM display.

* About the Time(ms) display

...

SDA

SCL

1 2 3 4 5 6 7 8 9

Displays the time from the reference point
to the 9

falling edge of the data.

Reference Point

1.5 Analyzing/Searching Data

Summary of Contents for DL7480

















































































































































































Search results

Summary of Contents for DL7480

Reviews:

Related manuals for DL7480

Brands by name

Popular brands

YOKOGAWA DL7480, User Manual

Search results

Summary of Contents for DL7480

Reviews:

Related manuals for DL7480

Brands by name

Popular brands