manualshive.com logo in svg

YOKOGAWA AQ7280 OTDR, User Manual

The YOKOGAWA AQ7280 OTDR is a cutting-edge optical time domain reflectometer. Ensure a smooth setup and operation with the comprehensive Getting Started Manual available for free download on our website. Discover all the essential information and step-by-step instructions to maximize the potential of this advanced product.

Share
Download
background image

4-6

IM AQ7280-01EN

5 Point Markers

  Press the 

5 Point Markers

 soft key to display the following screen.

  

Sets marker.

Press this soft key to select 

the marker that you are 

operating.

Marker information

Press to set all markers 

together.

Cursor (C)

Marker f

Marker F

Marker E

Marker N

Marker n

Note

•  Set the markers in the order shown above, starting with the measurement start point (the distance 

reference).

•  The measured loss value differs depending on the specified approximation method.
•  Set the correct position for marker E. The splice loss changes greatly depending on the position of E.

Presetting Markers

This function can be used to register markers that you set from the marker menu (2 Point Markers, 
4 Point Markers, 5 Point Markers, 6 Point Markers) in advance and apply them on waveforms with a 
single touch operation. Up to two sets of markers can be registered. This function is convenient when 
measuring the same event repeatedly for each core such as in a multi-core fiber measurement.

1.

  From the top menu, select 

OTDR

.

2.

  Press the 

Marker

 soft key to display the marker menu.

3.

  Press the 

Preset 

soft key to display the preset menu.

Preset A marker

Selects the preset action 

(Register, Delete, SetMarker)

Preset B marker

Preset information 

display screen

4.1  Analyzing Waveforms

Summary of Contents for AQ7280 OTDR




































































































































































































Reviews:

No comments

Related manuals for AQ7280 OTDR

TaiDoc L1 Owner'S Manual preview
L1
Brand: TaiDoc Pages: 31
3M Workstation Monitor 724 Instructions Manual preview
Workstation Monitor 724
Brand: 3M Pages: 21
3M SE-400 Series Getting Started preview
SE-400 Series
Brand: 3M Pages: 2
3M SD-200 Quick Start preview
SD-200
Brand: 3M Pages: 2
3M Dynatel 965AMS User Manual preview
Dynatel 965AMS
Brand: 3M Pages: 24
3M Dynatel 2250M Quick Manual preview
Dynatel 2250M
Brand: 3M Pages: 2
3M SoundPro SE Series Data Addendum Manual preview
SoundPro SE Series
Brand: 3M Pages: 293
FARMSCAN Jackal v2 Manual preview
Jackal v2
Brand: FARMSCAN Pages: 28
Keithley 236 Service Manual preview
236
Brand: Keithley Pages: 138
Hama TH-200 Operating Instruction preview
TH-200
Brand: Hama Pages: 6
J.P. Instruments EDM-900 Pilot'S Manual Addendum preview
EDM-900
Brand: J.P. Instruments Pages: 9
J.ASSY VISUM Monitor Technical Manual preview
VISUM Monitor
Brand: J.ASSY Pages: 13
Make Noise PHONOGENE Owner'S Manual preview
PHONOGENE
Brand: Make Noise Pages: 15
Major tech MT785 Instruction Manual preview
MT785
Brand: Major tech Pages: 40
WAGO I/O-SYSTEM 750 User Manual preview
I/O-SYSTEM 750
Brand: WAGO Pages: 96
Palstar ZM-30 Owner'S Manual preview
ZM-30
Brand: Palstar Pages: 37
LD Didactic Pocket-CASSY 2 Operating Instructions preview
Pocket-CASSY 2
Brand: LD Didactic Pages: 2
Kawai CN33 Owner'S Manual preview
CN33
Brand: Kawai Pages: 72

Brands by name

Popular brands

Load more brands