manualshive.com logo in svg

YOKOGAWA AQ7280 OTDR, User Manual

The YOKOGAWA AQ7280 OTDR is a cutting-edge optical time domain reflectometer. Ensure a smooth setup and operation with the comprehensive Getting Started Manual available for free download on our website. Discover all the essential information and step-by-step instructions to maximize the potential of this advanced product.

Share
Download
background image

2-15

IM AQ7280-01EN

Optical Pulse Measurement (OTDR)

1

2

3

4

5

6

7

8

Index

2.2  Performing Averaged Measurements

 WARNING

•  During measurement, light is transmitted from the light source ports. Do not disconnect the 

connected optical fiber cables. Visual impairment may occur if the light enters the eye.

•  Close the covers of any light source ports that do not have optical fiber cables connected 

to them. Visual impairment may occur if light that is mistakenly emitted from these ports 
enters the eye.

French

 AVERTISSEMENT

•  Lorsque l’AQ7280 génère de la lumière, la lumière est émise à travers les ports de source 

lumineuse. Ne pas débrancher les câbles de fibre optique connectés. Des lésions oculaires 
peuvent être causées si le faisceau lumineux pénètre l’œil.

•  Couvrir les caches des ports de source lumineuse libres. Sur les modèles dotés de deux 

ports de source lumineuse ou plus, protéger les yeux contre l’émission accidentelle de 
lumière depuis le mauvais port.

In averaged measurements, the data that is acquired from each pulse is averaged and displayed. By 
performing averaged measurements, you can improve the signal-to-noise (S/N) ratio.
This is effective when you want to detect faint events that are buried in noise.

Procedure

Starting and Stopping Measurements

1.

  From the top menu, select 

OTDR

.

2.

 Press 

AVG

. The measurement begins, and the measurement waveform is displayed on the 

screen.

The Average menu appears. The average duration or progress is displayed in the top area of the screen. 
Also, during measurement, a mark appears at the top of the display to indicate that the laser light is on.

Waveform display screen

(See section 3.1.)

Laser on indication

Average duration or progress

Set markers.

See section 4.1.

Set a comment

(up to 30 characters).

Enter a comment by 

following the procedure 

provided in “Entering 

Character Strings” in the 

Getting Started Guide, 

IMAQ7280-02EN.

Create a label.

(See section 6.3.)

Summary of Contents for AQ7280 OTDR




































































































































































































Reviews:

No comments

Related manuals for AQ7280 OTDR

Labom BA Series Operating Instructions preview
BA Series
Brand: Labom Pages: 5
Gazelle G9407-Log Operating Instruction preview
G9407-Log
Brand: Gazelle Pages: 2
Underground Magnetics Mag 3 Operator'S Manual preview
Mag 3
Brand: Underground Magnetics Pages: 48
JENCO EC3840 Operation Manual preview
EC3840
Brand: JENCO Pages: 13
Ametek Universal Analyzers 275E Instruction Manual preview
Universal Analyzers 275E
Brand: Ametek Pages: 34
Topcon IM-600 Instruction Manual preview
IM-600
Brand: Topcon Pages: 59
ASCOM TEMS AUTOMATIC - 2 Brochure preview
TEMS AUTOMATIC - 2
Brand: ASCOM Pages: 12
Tektronix KEITHLEY 4200-CVU-PWR Quick Start Manual preview
KEITHLEY 4200-CVU-PWR
Brand: Tektronix Pages: 6
Datcon DT4120 PS Series Operating Instructions Manual preview
DT4120 PS Series
Brand: Datcon Pages: 92
Eno Scientific Well Watch 700 User Manual preview
Well Watch 700
Brand: Eno Scientific Pages: 47
Kawai CN25 Operation Manual preview
CN25
Brand: Kawai Pages: 2
Korg PA 900 Musikant User Manual preview
PA 900 Musikant
Brand: Korg Pages: 20
DAKOTA ULTRASONICS PZX-7 Operation Manual preview
PZX-7
Brand: DAKOTA ULTRASONICS Pages: 51
Tusa ZEN AIR IQ-950 Owner'S Manual preview
ZEN AIR IQ-950
Brand: Tusa Pages: 137
OHAUS CKW Calibration Manual preview
CKW
Brand: OHAUS Pages: 2
YOKOGAWA Vigilantplant NFAI135 User Manual preview
Vigilantplant NFAI135
Brand: YOKOGAWA Pages: 24
SAGE Analytics The Luminary Quick Start Manual preview
The Luminary
Brand: SAGE Analytics Pages: 2
KUSSMAUL 091-198-12-PP Instruction Manual preview
091-198-12-PP
Brand: KUSSMAUL Pages: 7

Brands by name

Popular brands

Load more brands