manualshive.com logo in svg

YOKOGAWA AQ7280 OTDR, User Manual

The YOKOGAWA AQ7280 OTDR is a cutting-edge optical time domain reflectometer. Ensure a smooth setup and operation with the comprehensive Getting Started Manual available for free download on our website. Discover all the essential information and step-by-step instructions to maximize the potential of this advanced product.

Share
Download
background image

8-8

IM AQ7280-01EN

8.5  Updating the Firmware

Procedure

Firmware Update Screen

On the top menu, press 

SETUP

 and then the 

Firmware Update

 soft key to display the following 

screen.

Set the save destination drive 

of the firmware update file

(Int. Memory, USB Memory 1, 

USB Memory 2, SD Card).

Executes firmware updating

Using the rotary knob and ENTER, 

select the firmware update file.

Explanation

•  Firmware update files are YMC files (e.g., AQ7280.YMC).
•  If necessary, you can change the file name, but on the extension. For details, see section 6.5.
•  When updating the firmware, connect the AC adapter to the AQ7280.
•  When a firmware update completes successfully, the AQ7280 will restart automatically.
•  If it fails, an error message will appear.
  Check the format and version of the firmware update file. For the procedure, see section 8.3.

Summary of Contents for AQ7280 OTDR




































































































































































































Reviews:

No comments

Related manuals for AQ7280 OTDR

UEi MM100 Instruction Manual preview
MM100
Brand: UEi Pages: 4
3nh HG Series Operation Manual preview
HG Series
Brand: 3nh Pages: 10
M & I Instruments 8218 Manual preview
8218
Brand: M & I Instruments Pages: 2
Olympus EPOCH 650 User Manual preview
EPOCH 650
Brand: Olympus Pages: 362
Olympus 27MG Getting Started Manual preview
27MG
Brand: Olympus Pages: 8
palintest Micro 800 Operating Instructions Manual preview
Micro 800
Brand: palintest Pages: 14
Yamaha ARIUS YDP-S34 Midi Reference preview
ARIUS YDP-S34
Brand: Yamaha Pages: 14
Yamaha Disklavier Mark II XG Series Advanced Operation Manual preview
Disklavier Mark II XG Series
Brand: Yamaha Pages: 12
VELOCICALC 5725 Operation And Service Manual preview
5725
Brand: VELOCICALC Pages: 10
Kawai DX800 Owner'S Manual preview
DX800
Brand: Kawai Pages: 40
Lutron Electronics YK-2001PHA Operation Manual preview
YK-2001PHA
Brand: Lutron Electronics Pages: 43
Lutron Electronics VB-8213 Operation Manual preview
VB-8213
Brand: Lutron Electronics Pages: 23
YZXStudio ZY1270 User Manual preview
ZY1270
Brand: YZXStudio Pages: 3
ERICHSEN 518 USB Operating Manual preview
518 USB
Brand: ERICHSEN Pages: 33
Kurzweil m230 User Manual preview
m230
Brand: Kurzweil Pages: 35
PHYWE Cobra SMARTsense Chloride Ion Operating Instructions preview
Cobra SMARTsense Chloride Ion
Brand: PHYWE Pages: 4
Readiness Systems AED Sentinel Installation Manual preview
AED Sentinel
Brand: Readiness Systems Pages: 16
BK Precision 2831C Lnstruction Manual preview
2831C
Brand: BK Precision Pages: 21

Brands by name

Popular brands

Load more brands