YOKOGAWA AQ7280 OTDR User Manual Download Page 160

Page: 160 / 195

6-29

IM AQ7280-01EN

File Operation and Printing

Index

6.11 Printing Saved Waveforms

Procedure

File Menu

Press

FILE

to display the File menu.

Set the action (File Print).

Configure the print settings.

You can set the printer maker,

print color, whether to print the

event list, and whether to print

the measurement date.

Start printing.

Using the

rotary knob

and

ENTER

, select a file

to print.

A check mark appears next to the selected file.

To clear the selection, press ENTER again.

Select the target drive

(Int. Memory, USB Memory 1,

USB Memory 2, SD Card).

Explanation

Action

Select File Print.

Configuring the Print Settings

• Maker

Fixed to Seiko Instruments. You cannot change it.

• Print Color

Fixed to black and white printing. You cannot change it.

• Event List

See the explanation in section 6.10.

• Measured Date

  The date when the waveform was saved can be printed (not the date of printing).
  OFF:   The date is not printed.
  ON:    The date is printed.

Save Destination Drive

For details, see the explanation in section 6.3.

Starting to Print

You can specify several saved SOR files and print screen images one at a time.

Note

•  Do not connect an incompatible printer.
•  For USB printers that have been tested for compatibility, contact your nearest YOKOGAWA dealer.
•  Only SOR files can be printed.

Summary of Contents for AQ7280 OTDR




































































































































































































Search results

Summary of Contents for AQ7280 OTDR

Reviews:

Related manuals for AQ7280 OTDR

Brands by name

Popular brands

YOKOGAWA AQ7280 OTDR, User Manual

Search results

Summary of Contents for AQ7280 OTDR

Reviews:

Related manuals for AQ7280 OTDR

Brands by name

Popular brands