manualshive.com logo in svg

YOKOGAWA AQ7280 OTDR, User Manual

The YOKOGAWA AQ7280 OTDR is a cutting-edge optical time domain reflectometer. Ensure a smooth setup and operation with the comprehensive Getting Started Manual available for free download on our website. Discover all the essential information and step-by-step instructions to maximize the potential of this advanced product.

Share
Download
background image

6-17

IM AQ7280-01EN

File Operation and Printing

1

2

3

4

5

6

7

8

Index

6.7  Copying and Deleting Folders

 CAUTION

Do not remove a USB memory device or turn off the power when the USB memory access 
indicator is blinking or when data is being saved or loaded from internal memory. Doing so 
may damage the storage medium (USB memory or internal memory) or corrupt its data.

French

 ATTENTION

N'enlevez pas un dispositif de mémoire USB et ne coupez pas l'alimentation électrique 
lorsque l'indicateur d'accès à la mémoire USB clignote ou lorsque les données sont en train 
d'être enregistrées ou chargées à partir d'une mémoire interne. Vous risqueriez
d'endommager le support de stockage (mémoire USB ou mémoire interne) ou les données 
qu'il contient.

Procedure

Copying or Deleting Folders

Press 

FILE

 to display the following screen.

Set the action

(Delete Folder, Copy Folder).

Select the target drive 

(copy source, delete)

(Int. Memory, USB Memory 1, 

USB Memory 2, SD Card).

Delete or set the copy destination.

This soft key is Delete or Dest. Folder depending on 

the Action setting.

Pressing the 

Dest. Folder

 soft key displays a screen 

for selecting the copy destination folder.

After selecting a folder on this screen, pressing the 

Copy

 soft key displays a confirmation message for 

executing the operation. Tap 

OK

 to execute it.

Using the 

rotary knob

 and 

ENTER

, select 

the folder to delete or copy.

Summary of Contents for AQ7280 OTDR




































































































































































































Reviews:

No comments

Related manuals for AQ7280 OTDR

TA Q Series Getting Started Manual preview
Q Series
Brand: TA Pages: 58
A&D MF-50 Instruction Manual preview
MF-50
Brand: A&D Pages: 74
Waterproof DRYSUIT Owner'S Manual preview
DRYSUIT
Brand: Waterproof Pages: 10
Ocean Optics USB2000 Installation And Operation Manual preview
USB2000
Brand: Ocean Optics Pages: 43
Ocean Technology Systems PDR-100 User Manual preview
PDR-100
Brand: Ocean Technology Systems Pages: 12
Ocean Reef GSM Mercury Instruction Manual preview
GSM Mercury
Brand: Ocean Reef Pages: 24
GREISINGER G 1690 Quick Reference Manual preview
G 1690
Brand: GREISINGER Pages: 20
NCS COLOURPIN II User Manual preview
COLOURPIN II
Brand: NCS Pages: 7
Ferret CFWF50A2 User Manual preview
CFWF50A2
Brand: Ferret Pages: 18
Lumel NR30BAC User Manual preview
NR30BAC
Brand: Lumel Pages: 40
MRC PVB-820 Operation Manual preview
PVB-820
Brand: MRC Pages: 14
Tonghui TH2689 Operation Manual preview
TH2689
Brand: Tonghui Pages: 65
NIEUWKOOP EC-95 Quick Manual preview
EC-95
Brand: NIEUWKOOP Pages: 2
Peavey bass guitars Owner'S Manual preview
bass guitars
Brand: Peavey Pages: 24
EIJKELKAMP 14.36 Operating Instructions Manual preview
14.36
Brand: EIJKELKAMP Pages: 11
RADWAG PUE C/31H Quick Start Manual preview
PUE C/31H
Brand: RADWAG Pages: 12
C. B. Gitty Crafter Supply 52-018-01 Assembly Instructions Manual preview
52-018-01
Brand: C. B. Gitty Crafter Supply Pages: 12
AEMC instruments MN379T User Manual preview
MN379T
Brand: AEMC instruments Pages: 4

Brands by name

Popular brands

Load more brands