manualshive.com logo in svg

YOKOGAWA AQ7280 OTDR, User Manual

The YOKOGAWA AQ7280 OTDR is a cutting-edge optical time domain reflectometer. Ensure a smooth setup and operation with the comprehensive Getting Started Manual available for free download on our website. Discover all the essential information and step-by-step instructions to maximize the potential of this advanced product.

Share
Download
background image

6-15

IM AQ7280-01EN

File Operation and Printing

1

2

3

4

5

6

7

8

Index

6.6  Creating Folders

 CAUTION

Do not remove a USB memory device or turn off the power when the USB memory access 
indicator is blinking or when data is being saved or loaded from internal memory. Doing so 
may damage the storage medium (USB memory or internal memory) or corrupt its data.

French

 ATTENTION

N'enlevez pas un dispositif de mémoire USB et ne coupez pas l'alimentation électrique 
lorsque l'indicateur d'accès à la mémoire USB clignote ou lorsque les données sont en train 
d'être enregistrées ou chargées à partir d'une mémoire interne. Vous risqueriez
d'endommager le support de stockage (mémoire USB ou mémoire interne) ou les données 
qu'il contient.

Procedure

Creating a Folder

Press 

FILE

 to display the following screen.

Set the action (Make Folder).

Select the target drive

(Int. Memory, USB Memory 1, 

USB Memory 2, SD Card).

Using the 

rotary knob

 and 

ENTER

, select 

where to create the folder.

Create the folder.

A character input dialog box will open.

Enter the folder name by following the procedure 

provided in “Entering Character Strings” in the 

Getting Started Guide, IM AQ7280-02EN.

Tapping 

Enter

 in the character input dialog box 

changes the folder name to the name you entered.

Summary of Contents for AQ7280 OTDR




































































































































































































Reviews:

No comments

Related manuals for AQ7280 OTDR

Keithley 199 Quick Reference Manual preview
199
Brand: Keithley Pages: 49
4iiii PRECISION Firmware Upgrade Instructions preview
PRECISION
Brand: 4iiii Pages: 3
Hameg HM8118 Operator'S Manual preview
HM8118
Brand: Hameg Pages: 44
Hameg HM8118 Manual preview
HM8118
Brand: Hameg Pages: 60
Hameg HM5014-2 Service Manual preview
HM5014-2
Brand: Hameg Pages: 28
HAMAR LASER STEALTH Series General Training Manual preview
STEALTH Series
Brand: HAMAR LASER Pages: 113
Idexx SediVue Dx User Manual preview
SediVue Dx
Brand: Idexx Pages: 6
IDEAL INDUSTRIES SignalTEK II Quick Reference Manual preview
SignalTEK II
Brand: IDEAL INDUSTRIES Pages: 10
M-system TR30 Instruction Manual preview
TR30
Brand: M-system Pages: 5
Vega VEGAFLEX 81 Mounting Instructions preview
VEGAFLEX 81
Brand: Vega Pages: 20
Vega VEGACAP 63 Supplementary Instructions Manual preview
VEGACAP 63
Brand: Vega Pages: 16
Vega VEGACAL 63 Specification Sheet preview
VEGACAL 63
Brand: Vega Pages: 2
OBD VD10 User Manual preview
VD10
Brand: OBD Pages: 5
Hach 2100A User Manual preview
2100A
Brand: Hach Pages: 96
Didactum Monitoring System 500 II DC Quick Start Manual preview
Monitoring System 500 II DC
Brand: Didactum Pages: 2
marposs M1 Star MBG Instruction Manual preview
M1 Star MBG
Brand: marposs Pages: 58
H.E. Anderson Ratio:Guard Advanced Manual preview
Ratio:Guard Advanced
Brand: H.E. Anderson Pages: 9
Industrial Scientific iTrans 77023554 Manual preview
iTrans 77023554
Brand: Industrial Scientific Pages: 94

Brands by name

Popular brands

Load more brands