YOKOGAWA AQ7280 OTDR User Manual Download Page 101

Page: 101 / 195

4-8

IM AQ7280-01EN

Measuring Distance

By placing the cursor on the acquired waveform, you can measure the distance to events such as

reflections and splice losses.

Using the Cursor to Measure the Distance

Follow the procedure below to measure the distance between the distance reference and the cursor.

From the top menu, select

OTDR

Turn the rotary knob to display the cursor.

Move the cursor to a position where an event is displayed.

Distance reference

(measurement start position)

Cursor

Distance from the distance reference

to the cursor

Note

The location where the AQ7280 and the optical fiber cable are connected is the distance reference. To
perform more accurate measurements, zoom in on the waveform.

Using Markers to Measure the Distance

Follow the procedure below to measure the distance between two markers.

From the top menu, select

OTDR

Press the

Marker

soft key and then the

2 Point Markers

soft key to display the following

screen.

Set marker

and marker

at positions where events are displayed.

Marker

and marker

Distance between marker

4.1 Analyzing Waveforms

Summary of Contents for AQ7280 OTDR




































































































































































































Search results

Summary of Contents for AQ7280 OTDR

Reviews:

Related manuals for AQ7280 OTDR

Brands by name

Popular brands

YOKOGAWA AQ7280 OTDR, User Manual

Search results

Summary of Contents for AQ7280 OTDR

Reviews:

Related manuals for AQ7280 OTDR

Brands by name

Popular brands