YOKOGAWA AQ2200 Series User Manual Download Page 58

Page: 58 / 183

1.11 Transceiver I/F Module

AQ2200-642 Transceiver I/F Module

TRANSCEIVER I/F MODULE

AQ2200-642

POWER SUPPLY

SIGNAL

OUTPUT

28W MAX

Signal output indication lamp

This lamp shows the status of

the power supply to the transceiver.

The lamp is lit when the output is on.

Signal output ON/OFF key

Turns the power supply to the

transceiver on or off.

Each time this key is pressed,

the power supply switches between

on and off.

Power supply port

Provides power to the transceiver.

Control/monitor signal port

Use to configure the transceiver

control signals or monitor the

power supply voltage and monitor

signals.

Lock lever release button

Releases the lock lever.

Lock lever

Used when installing and

uninstalling the module.

Fixing screw

When you install the module, tighten

the screws to fix the module in place.

1-25

IM 735101-01EN

Component Names and Functions

Index

Summary of Contents for AQ2200 Series
























































































































































































Search results

Summary of Contents for AQ2200 Series

Reviews:

Related manuals for AQ2200 Series

Brands by name

Popular brands

YOKOGAWA AQ2200 Series, User Manual

Search results

Summary of Contents for AQ2200 Series

Reviews:

Related manuals for AQ2200 Series

Brands by name

Popular brands