manualshive.com logo in svg

YOKOGAWA AQ1215A, User Manual, Page: 248 / 282

Share
Download
YOKOGAWA AQ1215A User Manual Download Page 248

10-4

IM AQ1210-01EN

10.3  Using the Network (LAN)

Procedure

Connecting the Wired LAN Adapter (communication dongle)

1.

  Connect a wired LAN adapter to the Type A USB port of the instrument.

 

  

AQ1210A, AQ1215A, 

AQ1210E, AQ1215E, 

AQ1215F, AQ1216F

Wired LAN adapter 

(communication dongle)

USB Type A 

(2 ports)

LAN cable

Note

Please use your own communication dongle. For the recommended communication dongles that can be 
used with this instrument, contact your nearest YOKOGAWA dealer.

Network Setup Screen

2.

 Press 

MENU

 to display the MENU screen.

3.

 Press 

SETUP

 to display the system setup screen.

4.

 Tap 

Network Setup

 to display the Network Setup screen.

 

  

Enables or disables the network 

(Valid, Invalid)

Set the user name and password.

Enter the user name and password by following the procedure 

provided in “Entering Character Strings” in the Getting Started 

Guide, IM AQ1210-02EN.

Set the timeout period 

(Infinite (0), 1 to 3600).

Set the DHCP 

(OFF, ON).

Set the TCP/IP parameters.

Applies the network settings

Summary of Contents for AQ1215A



























































































































































































































































































Reviews:

No comments