YOKOGAWA AQ1215A User Manual Download Page 167

Page: 167 / 282

7-36

IM AQ1210-01EN

Connecting the Fiber Inspection Probe

Connect the fiber inspection probe to the USB port (Type A) of this instrument.

Connect the probe of the fiber inspection probe to the end face of the optical fiber cable.

Note

For instructions on how to use the fiber inspection probe, see the user’s manual for the probe.

Soft Key Menu (fiber inspection probe)

Tap the soft key menu display button. A soft key menu for the fiber inspection probe appears.

Soft key menu

Fiber Inspection Probe Menu

Displays the image in real time

Holds the image display (HOLD)

Starts saving

Press this soft key to save the still image to a BMP file. For the procedure

to set the file save destination and file name, see section 9.4.

Executes pass/fail judgment

A pass/fail judgment is performed, and the result (summary) is displayed.

Displays results

Displays the judgment results (detail)

7.6 Using the Fiber Inspection Probe (/FST option)

Summary of Contents for AQ1215A



























































































































































































































































































Search results

Summary of Contents for AQ1215A

Reviews:

Related manuals for AQ1215A

Brands by name

Popular brands

YOKOGAWA AQ1215A, User Manual

Search results

Summary of Contents for AQ1215A

Reviews:

Related manuals for AQ1215A

Brands by name

Popular brands