YOKOGAWA AQ1215A User Manual Download Page 11

Page: 11 / 282

1-5

IM AQ1210-01EN

Features

App

Index

System Configuration

USB TypeC

AQ1210A, AQ1215A,

AQ1210E, AQ1215E,

AQ1215F, AQ1216F

Three-prong

outlet

USB-AC

adapter

USB cable

USB memory (section 9.1)

Fiber inspection probe (section 7.6)

• Mass storage device (section 9.2)

• Remote control (section 10.4)

• Charging the instrument

See the Getting Started Guide, IM AQ1210-02EN.

Communication dongle

(section 10.3) (WLAN, LAN)

OTDR port 2

• OTDR measurement

(wavelength 1625 nm, 1650 nm)

• Light source output

OTDR port 1

• OTDR measurement

(wavelength 1310 nm, 1550 nm)

• Light source output, power checker

measurement

OPM port

Optical power meter input

(/SPM, /HPM, /PPM option)

VLS Port

VLS output (wavelength 650 nm)

(/VLS option)

USB TypeC

USB Type A

(2 ports)

USB cable (standard

accessory)

See the top panel in “Component

Names and Functions” in the

Getting Started Guide, IM

AQ1210-02EN.

1.1 Overview

Summary of Contents for AQ1215A



























































































































































































































































































Search results

Summary of Contents for AQ1215A

Reviews:

YOKOGAWA AQ1215A, User Manual, Page: 11 / 282

Search results

Summary of Contents for AQ1215A

Reviews: