manualshive.com logo in svg

YOKOGAWA AF220, Application Note

Share
Download
YOKOGAWA AF220 Application Note Download Page 17

 

 

 

F²MC-16LX Family, Flash Programmer Yokogawa AF220/221 

www.cypress.com

 

Document No. 002-05108 Rev. *B 

17 

7 

Pass/Error Adapter AZ266 

This chapter describes how to output the programming result  

For extended functionality within an assembly line, the Pass/Error adapter AZ266 (see chapter 1.6) may be helpful to 
output the result of programming. 

By this adapter, communication with a SPS-interface is possible. 

 

Figure 20. Pass/Error adapter AZ266 

 
 
 
 
 
 
 
 
 
 
 
 
 
 
 

 

Table 4. Function results 

Function 

PASS 

ERROR 

ERASE 

Chip was erased successfully 

Chip erase failed 

BLANK CHECK 

Chip is empty 

Chip is not empty 

PROGRAM 

Program ended successfully 

Programming failed 

READ 

Verify okay 

Verify failed 

E.P.R. 

Automatic programming  

ended successfully 

Automatic programming failed 

 

 

 

 
 
 

Yokogawa 

Flash-Programmer 

AF220 

 
 
 

PASS/ERROR 

Adapter 

AZ266 

Ext.KEY 

PASS 

ERROR 

Start Programming 

OAK1 

OAK2 

Summary of Contents for AF220























Reviews:

No comments

Brands by name

Popular brands

Load more brands