background image

 

 

<1.  Introduction>

1

IM 01E21A01-03EN-A

1st Edition: Mar. 2020 (KP)

All Rights Reserved, Copyright © 2020, Yokogawa Electric Corporation

1. 

Introduction

This manual provides the basic guidelines for installation, 
wiring procedures and basic operation of ADMAG TI (Total 
Insight) Series AXG magnetic flowmeters with EtherNet/IP 

protocol.

For the items which are not covered in this manual,
read the applicable user’s manuals and general
specifications as listed in Table 1.1. These documents can 
be downloaded from the YOKOGAWA website. To ensure 
correct use of the product, read these manuals thoroughly 
and fully understand how to operate the product before 
operating it. For method of checking the model and 
specifications, read Chapter 2 and general specifications 

as listed in Table 1.1.

Website address: http://www.yokogawa.com/fld/doc/
These manuals can be downloaded from the website 
of YOKOGAWA or purchased from the YOKOGAWA 

representatives.

Table 1.1

    Manual and General Specifications List

Model

Document Title

Document No.

AXG###
AXG4A

ADMAG TI Series
AXG###, AXG4A Magnetic 

Flowmeter

EtherNet/IP communication type

Read Me First

IM 01E21A21-
04EN-A

ADMAG TI Series
AXG Magnetic Flowmeter
Installation Manual

IM 01E22A01-01EN

ADMAG TI Series
AXG Magnetic Flowmeter
EtherNet/IP Communication Type
Installation Manual 
Difference to IM 01E22A01-01EN

IM 01E21A01-03EN-A 
(this manual)

ADMAG TI Series
AXG Magnetic Flowmeter

Maintenance Manual

IM 01E22A01-02EN

ADMAG TI Series
AXG Magnetic Flowmeter
General Specification

GS 01E22A01-01EN

ADMAG TI Series
AXG Magnetic Flowmeter
EtherNet/IP Communication Type

IM 01E21A02-06EN

ADMAG TI Series 
AXG Magnetic Flowmeter
EtherNet/IP Communication Type

GS 01E21F02-02EN-A

NOTE

When describing the model name like AXG### in this 
manual, “###” means any of the following.
002, 005, 010, 015, 025, 040, 050, 080, 100, 150, 200

„

  Precautions Related to the Protection, 

Safety, and Alteration of the Product

(Please read the descriptions on IM 01E22A01-01EN.)

„

  Regarding This User’s Manual

(Please read the descriptions on IM 01E22A01-01EN.)

„

  Trademarks:

(Please read the descriptions on IM 01E22A01-01EN, 
and add the following description.)

•  “EtherNet/IP”, “CIP” and “ODVA” are registered 

trademark of ODVA Inc.

1.1  For Safe Use of Product

System in which this product is incorporated, be sure to 
follow the instructions and precautions on safety that is 
stated in this manual whenever you handle the product. 
Take special note that if you handle the product in a 
manner that violated these instructions, the protection 
functionality of the product may be damaged or impaired. 
In such cases, YOKOGAWA shall not be liable for any 
indirect or consequential loss incurred by either using or 
not being able to use the Product.

(1)  General

•  This product conforms to IEC safety class I (with 

Protective grounding terminal), Installation Category 
(Overvoltage Category) II, No Measurement Category 
(“O”(Other)), Micro Pollution degree 2, Macro 
Pollution degree 4, Altitude at installation Site Max. 

2000 m above sea level.

•  This product is an EN61326-1 (EMC standard), Class A (for 

use in commercial, industrial, or business environments).

•  This product conforms to the standard specifications 

of CIP for EtherNet/IP communication.

•  This product is complied with IP66 and IP67 in the 

EN60529. YOKOGAWA assumes no liability for the 
customer’s failure to comply with these requirements.

•  This product is designed for indoor and outdoor use.

CAUTION

This product is a Class A product in the EN61326- 
1(EMC standard). Operation of this product in a 
residential area may cause radio interference, in 
which case the user is required to take appropriate 
measures to correct the interference.

IMPORTANT

The minimum ambient temperature is limited by the 
minimum fluid temperature of the sensor (the lining). 
For more information, read the applicable general 
specifications as listed in Table 1.1. The flowmeter 
may be used in an ambient humidity where the relative 
humidity ranges from 0 to 100%. However, avoid long-
term continuous operation at relative humidity above 
95%.

Summary of Contents for ADMAG AXG Series

















Reviews: