YOKOGAWA ADMAG AXG Series User Manual Download Page 15

Page: 15 / 16

Errors and Countermeasures

(Display unit)

System Alarm

(Please read the descriptions on IM 01E22A01-01EN, and add the following description.)

Table System Alarm

NE107
Status

Error Message

Error Description

Countermeasure

Display

200:Opt bd comm ERR1

Communication error of EtherNet/IP board was detected.

Contact Yokogawa service center.

201:Opt bd comm ERR2

Communication error of EtherNet/IP board was detected.

Contact Yokogawa service center.

Process Alarm

(Please read the descriptions on IM 01E22A01-01EN.)

Setting Alarm

(Please read the descriptions on IM 01E22A01-01EN.)

Warning

(Please read the descriptions on IM 01E22A01-01EN.)

Information

(Please read the descriptions on IM 01E22A01-01EN.)

<7. Errors and Countermeasures (Display unit)>

IM 01E21A01-03EN-A

Summary of Contents for ADMAG AXG Series

















Search results

Summary of Contents for ADMAG AXG Series

Reviews:

Related manuals for ADMAG AXG Series

Brands by name

Popular brands

YOKOGAWA ADMAG AXG Series, User Manual

Search results

Summary of Contents for ADMAG AXG Series

Reviews:

Related manuals for ADMAG AXG Series

Brands by name

Popular brands