manualshive.com logo in svg

YOKOGAWA 701931, User Manual

Share
Download
YOKOGAWA 701931 User Manual Download Page 3

ii

IM 701931-01E

Checking the Contents of the Package

If the wrong instrument or accessories have been delivered, or if some 
accessories are missing or defective, contact the dealer from which you 
purchased them.

Current Probe (Model 701931) Main Body
Accessories
•  User’s manuals 

1 set

•  Carrying case

Safety Precautions

This probe meets the requirements as given in the IEC-61010.
The following general safety precautions must be observed during all phases of 
operation, service, and repair of this instrument. If this instrument is used in a 
manner not specified in this manual, the protection provided by this instrument 
may be impaired. Also, YOKOGAWA assumes no liability for the customer’s 
failure to comply with these requirements.

The following symbols are used on this instrument.

  To avoid injury, death of personnel or damage to the instrument, the 

operator must refer to an explanation in the User’s Manual or Service 
Manual.

  Both direct and alternating current.

  Do not apply around or remove from HAZARDOUS LIVE conductors.

Summary of Contents for 701931





















Reviews:

No comments

Brands by name

Popular brands

Load more brands