manualshive.com logo in svg

YOKOGAWA 701210, User Manual, Page: 74 / 747

Share
Download
YOKOGAWA 701210 User Manual Download Page 74

2-36

IM 701210-05E

2.4 Setting Waveform Acquisition Conditions and Display Conditions

Action-on-Stop <Section 6.18>

A specified action can be carried out when the waveform is displayed after acquiring the

specified record length of data or when measurement is stopped after the measurement

is started.

• Print the Screen Image Data (PRINT)

Prints the screen image data to a specified printer.

• Save the Screen Image Data (Image)

Saves the screen image data to the save destination specified in the IMAGE SAVE

menu.

• Save Waveform Data (Save to File)

Saves the waveform data in binary, ASCII, or floating format to the save destination

specified in the FILE menu.

• Beep Sound (Buzzer)

Sounds a buzzer.

• Send Mail

Sends an e-mail message to a specified address  (when the Ethernet interface option

is installed).

Voice Memo Function <Sections 3.14 and 7.9>

Target 
waveform

Event 
waveform

Voice memo

When in roll mode display

Voice memo is also saved 
as waveform data when the
waveform data is saved.

Voice memos can be recorded while waveforms are being acquired (when in roll mode

display).  The recording and playing of voice memos are done by connecting an optional

earphone microphone with a PUSH switch (sold separately).  By connecting a speaker,

the voice memo can also be played through a speaker.  The recorded voice memo can

be saved along with the waveform data.  The voice memo can be played by loading the

saved waveform data.

The voice memo function can perform the following operations.

Record:

Record mode is enabled by turning ON the PUSH switch of the earphone

microphone.  The maximum record time is 100 s.

Save/Load:

To save the voice memo, save the waveform data that has the voice

memo recorded (waveform data in binary format or realtime recorded

waveform data).  The voice memo is loaded by loading the saved

waveform data allowing it to be played.

Play:

When waveform data that has a voice memo recorded is selected, the

recorded voice memo is played.

Note

•

The voice memo remains only on the newest waveform data that has been stored in the
acquisition memory.  If you restart data acquisition without saving the waveform data, the
voice memo that was attached to the previous waveform will be cleared.

•

Voice memos are backed up by the backup function of the acquisition memory.

Backing Up the Acquisition Memory <Section 7.10>

If the ACQ MEMORY BACKUP switch on the right side panel of the DL750/DL750P is

turned ON, the history memory data in the acquisition memory, the sub window data of

the dual capture function, and the voice memo data are backed up even if the power

supply is cut off.  The data held in the acquisition memory is backed up immediately

before the power is turned OFF.  This function protects the data in the acquisition

memory from sudden power failures.

Alkaline dry cells or nickel hydride rechargeable batteries (four AAA batteries) are

required for the backup.  The backup time varies depending on the operating

environment.  For reference values of the backup time, see section 19.5, “Function.”

Summary of Contents for 701210












































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments