manualshive.com logo in svg

YOKOGAWA 701210, User Manual, Page: 53 / 747

Share
Download
YOKOGAWA 701210 User Manual Download Page 53

2-15

IM 701210-05E

Explanation of Functions

2

2.2 Setting the Horizontal and Vertical Axes

Acceleration Measurement <Section 5.18>

The Acceleration Module (with AAF) (701275 (ACCL/VOLT)) measures acceleration

using the output signal from the acceleration sensor.  Direction connection is possible to

a built-in amplifier type acceleration sensor.  (Direct connection is not possible to a

charge output type acceleration sensor that does not have a built-in amplifier.  For details

on the connection of the acceleration sensor, see section 3.12.)

Note

The 701275 (ACCL/VOLT) can also measure voltage.

Current Supply to Acceleration Sensors

The 701275 (ACCL/VOLT) can supply 4 mA of current to the acceleration sensor when

measuring acceleration.

Note

If you supply current to the acceleration sensor before it is connected to the item under
measurement, the internal circuit of the acceleration sensor may be damaged.  Be sure to
supply current after connecting the acceleration sensor.

Filter

If you set the bandwidth limit to Auto, the anti-aliasing filter (AAF) and low-pass filter are

enabled depending on the sample rate to eliminate high-frequency noise from the input

signal.  Using the anti-aliasing filter when measuring voltage allows elimination of

aliasing noise resulting from FFT computation, digital filter computation of DSP channels,

etc.  For details on the bandwidth limit, see section 5.7.

Note

The filter is effective not only during acceleration measurement but also during voltage
measurement.

Summary of Contents for 701210












































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments