YOKOGAWA 701210 User Manual Download Page 46

Page: 46 / 747

2-8

IM 701210-05E

2.2 Setting the Horizontal and Vertical Axes

Input Coupling <Section 5.5>

If you wish to observe just the amplitude of an AC signal, it is best to remove the DC

component from the input signal. On the other hand, there are times when you wish to

check the ground level or observe the entire input signal (both the DC and AC

components). In these cases, you change the input coupling setting. By changing the

input coupling, the input method used to input the signal to the vertical control circuit

(voltage axis) is switched.

Select from the following types of input coupling.

The input signal is directly coupled to the attenuator of the vertical control circuit. Select

DC when you wish to observe the entire input signal (DC and AC components).

AC (Only When Observing the Voltage)

The input signal is coupled to the attenuator of the vertical control circuit through a

capacitor. Select AC when you wish to observe only the amplitude of the AC signal,

eliminating the DC components from the input signal.

GND

Input signal is coupled to the ground not to the attenuator of the vertical control circuit.

By selecting GND, you can check the ground level on the screen.

Vertical

control

circuit

Input
terminal

1 M

Ω

Input
terminal

1 M

Ω

Input
terminal

GND

Vertical

control

circuit

Vertical

control

circuit

TC (Only When Observing the Temperature)

Select TC when observing the temperature on the 701261 (UNIVERSAL), 701262

(UNIVERSAL (AAF)), or 701265 (TEMP/HPV).

DC-RMS

Using the 701260 (HV (with RMS)), both the DC and AC components of the signal are

converted to rms values and displayed. A RMS conversion circuit is connected to the vertical

control circuit of the same input coupling circuit used when the coupling is set to “DC.”

AC-RMS

Using the 701260 (HV (with RMS)), only the AC component of the signal is converted to

rms values and displayed. A RMS conversion circuit is connected to the vertical control

circuit of the same input coupling circuit used when the coupling is set to “AC.”

Vertical

control

circuit

Input
terminal

1 M

Ω

Vertical

control

circuit

Input
terminal

1 M

Ω

DC-RMS

AC-RMS

RMS

conversion

circuit

RMS

conversion

circuit

ACCL (Only When Measuring Acceleration)

Select ACCL when measuring acceleration on the 701275 (ACCL/VOLT).

Summary of Contents for 701210












































































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for 701210

Reviews:

YOKOGAWA 701210, User Manual, Page: 46 / 747

Search results

Summary of Contents for 701210

Reviews: