YOKOGAWA 701210 User Manual Download Page 342

Page: 342 / 747

9-23

IM 701210-05E

Recording in Recorder Mode (Realtime Recording) (Only on the DL750P)

Explanation

The measured data of the T-Y waveform recorded in Chart Recorder mode or the

measured data of the X-Y waveform recorded in X-Y Recorder mode is stored in the

internal memory.

Reprinting the Waveform Recorded in Chart Recorder Mode (T-Y Waveform Recording)

Print to

To reprint the waveform recorded in Chart Recorder mode (T-Y waveform recording), set

the print destination to Printer (built-in printer).

Length

Continue:

Prints the range specified by Window Mag/Window Pos and Start Point/

End Point using the magnification specified by Print Mag.

A4 Print:

Prints the range specified by Window Mag/Window Pos and Start Point/

End Point to A4 size. The magnification changes automatically so that the

specified print range fits on an A4 size paper.

Selecting the Section to Be Reprinted

Zoom Rate/Zoom Position: Window Mag/Window Pos

When selecting the section to be reprinted, Window Mag is used to reduce the zoom rate

in order to redisplay the waveform that has been cleared from the screen. You can also

move Window Pos to redisplay the waveform that had been cleared from the screen.

Start Point/End Point

If Length is set to Continue, display the section to be reprinted on screen, and then

use Start Point and End Point to set the start and end points.

After displaying the section to be reprinted on screen, use Start Point and End Point

to set the start and end points.

Print Magnification: Print Mag

Set Print Mag on when Length is set to Continue.

Set the waveform magnification for reprinting. The top section of the menu shows the

magnification; the bottom section shows the number of pages when the waveform is

recorded using the magnification indicated in the top section.

Reduce the zoom ratio to
display the section you wish
to reprint on the screen

Set the Start Point and
End Point

Set the magnification
of the section you
wish to reprint with
Output Mag
Reprinting

Move Window Pos to the left
to display the section you
wish to reprint on the screen

Waveform cleared
from the screen

Section you wish
to reprint

Window

Mag

Window

Pos

Start Point End Point

Start Point

End Point

When Length is set to Continue

When Length is set to A4 Print

The magnification of the waveform displayed on
the screen is automatically adjusted to fit on an
A4 size paper, and the waveform is printed.

9.8 Reprinting on the Built-in Printer

Summary of Contents for 701210












































































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for 701210

Reviews:

YOKOGAWA 701210, User Manual, Page: 342 / 747

Search results

Summary of Contents for 701210

Reviews: