YOKOGAWA 701210 User Manual Download Page 320

Page: 320 / 747

9-1

IM 701210-05E

Recording in Recorder Mode (Realtime Recording) (Only on the DL750P)

Chapter 9

Recording in Recorder Mode (Realtime Recording) (Only on the DL750P)

9.1

Loading the Roll Paper into the DL750P Built-in
Printer

This section describes how to load the DL750P roll paper. For the procedure to load the

DL750 roll paper, see section 12.1.

Printer Roll Paper

Use a dedicated roll paper (for the DL750P) that is provided by YOKOGAWA. Do not

use other types of roll paper. When you are using the printer for the first time, use the

roll paper that comes with the package. Order extra rolls from your nearest

YOKOGAWA dealer.

Part No.:

701966

Specifications: Thermal paper, 20 m

Minimum Q’ty: 6 rolls

Roll Paper Handling

The paper is a Thermal paper that changes color with the application of heat. Note the

following:

Storage Precautions

The paper starts changing color at around 70

C. It is affected by heat, humidity, light,

and chemicals regardless of whether the paper has been used.

• Store the paper rolls in a cool, dry, and dark place.

• After opening the package, use it quickly.

• If the paper is left in contact with plastic film containing plasticizers (such as a vinyl

chloride film or Scotch tape) for an extended time, the paper will lose some of its

ability to reproduce color. If you are going to store the paper in a folder, for example,

use a folder made of paper stock or polypropylene.

• When using glue on the paper, do not use glue containing organic solvents such as

alcohol or ether, as they will change the color of the paper.

• For prolonged storage, we suggest you make copies of results printed on the roll

paper. Due to the characteristics of the Thermal paper, the recording section may

lose color over time.

Handling Precautions

• Be sure to use only genuine paper rolls provided by YOKOGAWA.

• Touching the paper with sweaty hands can leave finger prints or blur the printing.

• Rubbing the surface with a hard object can cause the paper to change color due to

the heat caused by friction.

• If chemicals, oil, or other liquids come in contact with the paper, the paper may

change color or the printing may fade.

Precautions to Be Taken When Using the Built-in Printer

Allow enough space around the output area of the printer. If the roll paper is

continuously fed out when the output area is close to a wall, for example, the roll paper

that has been delivered may reenter the output area and get entangled.

Summary of Contents for 701210












































































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for 701210

Reviews:

YOKOGAWA 701210, User Manual, Page: 320 / 747

Search results

Summary of Contents for 701210

Reviews: