YOKOGAWA 701210 User Manual Download Page 303

Page: 303 / 747

8-7

IM 701210-05E

Display

Explanation

Normally, the display is updated every time the trigger is activated making it difficult to

capture transient conditions such as sudden distortion of waveforms. By using the

accumulate function, the waveform display of the acquired data remains on the screen

for the specified time.

Accumulate Mode

Persist: Persistence mode. Accumulates in red. Displayed for the specified time period

by gradually lowering the brightness.

Accumulate Period: Count

When using persistence mode, set the number of times to accumulate the waveform in

the range of 2 to 128 (in 2

steps). If you select Infinite, the accumulation is carried out

infinitely. The default value is 16.

Notes When Using Accumulation

• Automated measurement of waveform parameters and GO/NO-GO determination are

performed on the newest waveform.

• When printing accumulated waveforms using the built-in printer, they are printed using

two tones.

• If the waveform acquisition is forcibly stopped by pressing START/STOP, the

accumulation is temporarily suspended. When the acquisition is restarted, the display

is cleared and accumulation continues.

• You cannot change the parameters on the HISTORY menu when accumulating

waveforms on the display.

• Accumulated display is not possible in roll mode display.

• When you turn OFF the accumulate mode, accumulated waveforms are cleared. To

display the acquired waveforms again, specify the record number on the HISTORY

menu.

• If you display the waveforms again by setting the accumulate mode to Persist, the

accumulated waveforms are not cleared. To clear them, execute CLEAR TRACE.

• Even if you change the display format during accumulated display, the waveforms that

are already displayed accumulated are not cleared. To clear them, execute CLEAR

TRACE.

Clearing Accumulated Waveforms

You can clear accumulated waveforms by pressing the CLEAR TRACE key.

8.4 Accumulated Waveform Display

Summary of Contents for 701210












































































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for 701210

Reviews:

YOKOGAWA 701210, User Manual, Page: 303 / 747

Search results

Summary of Contents for 701210

Reviews: