manualshive.com logo in svg

YOKOGAWA 701210, User Manual, Page: 299 / 747

Share
Download
YOKOGAWA 701210 User Manual Download Page 299

8-3

IM 701210-05E

Display

8

8.2

Setting the Display Interpolation Method

<For a description of this function, refer to page 2-37.>

Procedure

MEASURE CURSOR

RESET

SELECT

CH

ALL  CH

MODE

POSITION

SIMPLE/ENHANCED

ACQ

START/STOP

SETUP

DISPLAY

ZOOM

DUAL

CAPTURE

HISTORY

MATH

 1

CH

 2

CH

 3

CH

 4

CH

 5

CH

 6

CH

 7

CH

 8

CH

 9

CH

 10

CH

 11

CH

 12

CH

 13

CH

 14

CH

 15

CH

 16

DELAY

MANUAL  TRIG

V/DIV

TIME/DIV

TRIGGER

TRIG  D

VERTICAL

HORIZONTAL

CAL

X-Y

SEARCH

7

DSP 1

8

9

DSP 2

6

5

4

1

0

2

3

ENTER

m

DSP 6

DSP 5

LOGIC  A

LOGIC  B

EVENT

DSP 3

DSP 4

EXP

GO/NO-GO

ACTION

FILE

SHIFT

1.

Press 

DISPLAY

.

Setting the Interpolation Method

2.

Press the 

Interpolation

 soft key.  The interpolation selection menu appears.

3.

Press the soft key corresponding to the desired interpolation method from 

OFF

,

Sine

, and 

Line

.

If you select OFF, proceed to step 4.

Setting the Number of Data Points to Be Used for Waveform Display

4.

Press the 

Decimation

 soft key to select the number of points to be used for the

display from 2k and 100k.

Note

Decimation specifies the number of dots when interpolation is turned OFF.  For example, if
the record length is 100 kW and Decimation is set to 2k, data is extracted at constant
intervals.  Waveform is displayed using 2 kW of data.  If Decimation is set to 100 k, the
waveform is displayed using all 100 kW of data.

Explanation

Setting the Interpolation Method

Any area along the time axis having less than 1000 points in 10 divisions (less than 500

points in the Z1 and Z2 window when displaying Main & Z1 & Z2) is recognized as an

interpolation area.  If you leave interpolation off, these points will appear as discrete dots

(so that the display will show gaps between dots or vertical lines).

If you set interpolation on, however, the DL750/DL750P will connect the points.  Three

following interpolation methods are available.

Sine(

): Interpolates between two points using the sin(x)/x function.

Line(

):

Linearly interpolates between two points.

OFF(

): No interpolation.

• When the Area Is Not an Interpolation Area

If interpolation is set to Sine or Line, the instrument draws lines between points that

are aligned vertically.

Interpolate

OFF

:

Sine

Line

Summary of Contents for 701210












































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments