Home
/
YOKOGAWA
/
701210
/
User Manual

YOKOGAWA 701210, User Manual, Page: 289 / 747

Share

Page: 289 / 747

YOKOGAWA 701210 User Manual Download Page 289

7-23

IM 701210-05E

Acquisition and Display

7

7.9

Using the Voice Memo Function

<For a description of this function, refer to page 2-36.>

This section describes only the voice memo function. For a description of the voice

comment function, see section 13.19.

Before using the voice memo function, connect the earphone microphone with a PUSH

switch to the DL750/DL750P by referring to section 3.14, “Connecting the Earphone

Microphone with a PUSH Switch and Connecting the Speaker.”

Note

•

The REC LEVEL and VOLUME knobs on the left side panel click in place at the center
position. When using the earphone microphone with a PUSH switch, set the REC LEVEL
and VOLUME knobs to the center position to obtain adequate recording level and play
volume.

•

If you are outputting the voice to an external speaker for the first time by using the optional
speaker cable (sold separately), set the play volume to the minimum setting using the
VOLUME knob.

Procedure

PROTECT

VOICE
MEMO

IMAGE

SAVE

PRINT

MENU

MENU

DL750

DL750P

SHIFT

HELP

MISC

NUM KEY

PROTECT

FEED

IMAGE

SAVE

PRINT

SNAPSHOT CLEAR TRACE

MENU

VOICE MEMO

MENU

MEASURE CURSOR

RESET

SELECT

CH

ALL CH

MODE

POSITION

SIMPLE/ENHANCED

ACQ

START/STOP

SETUP

DISPLAY

ZOOM

DUAL

CAPTURE

HISTORY

MATH

1

CH

2

CH

3

CH

4

CH

5

CH

6

CH

7

CH

8

CH

9

CH

10

CH

11

CH

12

CH

13

CH

14

CH

15

CH

16

DELAY

MANUAL TRIG

V/DIV

TIME/DIV

TRIGGER

TRIG D

VERTICAL

HORIZONTAL

CAL

X-Y

SEARCH

7

DSP 1

8

9

DSP 2

6

5

4

1

0

2

3

ENTER

m

DSP 6

DSP 5

LOGIC A

LOGIC B

EVENT

DSP 3

DSP 4

EXP

GO/NO-GO

ACTION

FILE

SHIFT

Setting the Voice Memo Function

1.

Press

VOICE MEMO

. (On the DL750P, press

SHIFT+FEED (VOICE MEMO)

.)

2.

Press the

Mode

soft key to select ON.

• Turning ON/OFF the Event Waveform Display

3.

Press the

Event Display

soft key to select OFF or ON. For a description of

event waveforms, see section 5.21.

4.

Press the

Next 1/2

soft key.

• Setting the Record Time

5.

Press the

Rec Time

soft key.

6.

Press the

Flexible

or

Fixed

soft key. If you wish to record for an arbitrary length

of time without specifying the record time, select Flexible; if you wish specify the

record time and count before recording, select Fixed. If you select Flexible

proceed to step 8; if you select Fixed proceed to step 7.

7.

Use the

jog shuttle

to set the Time in the range of 5 s * 20 (5 s

×

20 times) to

100 s * 1 (100 s

×

1 time).

«
...
287
288
289
290
291
...
»

Summary of Contents for 701210












































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments