YOKOGAWA 701210 User Manual Download Page 286

Page: 286 / 747

7-20

IM 701210-05E

7.8

Setting the Action When Waveform Display Is
Updated (Action-on-Stop)

<For a description of this function, refer to page 2-36.>

Procedure

Press

SHIFT+MODE

to display the ACTION menu.

Setting the Action

Press the

Mode

soft key to display the Mode setup menu.

Press the

On Stop

soft key.

Press the

Action

soft key to display the Action setup menu.

Use the

jog shuttle

and

SELECT

to select action to be enabled. (You can

select multiple actions.)

If you selected Save to File in step 3, use the

jog shuttle

and

SELECT

to set

the file save format to Binary, ASCII, or Float. If you selected Send Mail, use

the

jog shuttle

and

SELECT

to set Mail Count.

Setting the Number of Actions

Press the

Sequence

soft key to select Single or Continue.

Press the

ACQ Count

sof key.

Turn the

jog shuttel

to set the numeber of actions. Pressing

RESET

resets the

count Infinite.

Setting the Execution Mode of the Action-on-Stop at Power ON

10.

Press

MISC

11.

Press the

Next 1/2

soft key

12.

Press the

Others

soft key.

13.

Press the

Action Mode (Power ON)

soft key to select ON or OFF.

Executing the Action-on-Stop

14.

Press

START/STOP

. Waveform acquisition is started, and action-on-stop is

executed. While action-on-stop is in execution,

is displayed in the upper left

corner of the screen.

In addition, if the following action is specified, the following icon is displayed in

the upper left corner of the screen while the action is being executed.

Image/Save to File:

Save destination medium (

FD,

Zip disk,

card,

SCSI device,

internal HD,

network drive,

USB storage device)

Send Mail:

MEASURE CURSOR

RESET

SELECT

ALL CH

MODE

POSITION

SIMPLE/ENHANCED

ACQ

START/STOP

SETUP

DISPLAY

ZOOM

DUAL

CAPTURE

HISTORY

MATH

DELAY

MANUAL TRIG

V/DIV

TIME/DIV

TRIGGER

TRIG D

VERTICAL

HORIZONTAL

CAL

X-Y

SEARCH

DSP 1

DSP 2

ENTER

DSP 6

DSP 5

LOGIC A

LOGIC B

EVENT

DSP 3

DSP 4

EXP

GO/NO-GO

ACTION

FILE

SHIFT

Summary of Contents for 701210












































































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for 701210

Reviews:

YOKOGAWA 701210, User Manual, Page: 286 / 747

Search results

Summary of Contents for 701210

Reviews: