YOKOGAWA 701210 User Manual Download Page 282

Page: 282 / 747

7-16

IM 701210-05E

7.7

Realtime Recording to the Internal Hard Disk
(Optional)

<For a description of this function, refer to page 2-35.>

Procedure

MEASURE CURSOR

RESET

SELECT

ALL CH

MODE

POSITION

SIMPLE/ENHANCED

ACQ

START/STOP

SETUP

DISPLAY

ZOOM

DUAL

CAPTURE

HISTORY

MATH

DELAY

MANUAL TRIG

V/DIV

TIME/DIV

TRIGGER

TRIG D

VERTICAL

HORIZONTAL

CAL

X-Y

SEARCH

DSP 1

DSP 2

ENTER

DSP 6

DSP 5

LOGIC A

LOGIC B

EVENT

DSP 3

DSP 4

EXP

GO/NO-GO

ACTION

FILE

SHIFT

Press

ACQ

Press the

RealTime Out

soft key to select HD.

Note

The RealTime Out menu does not appear if Time Base is set to Ext.

Setting the Realtime Recording

Press the

RealTime Out Setup

soft key. A setup dialog box opens.

Use the

jog shuttle

and

SELECT

to set Sequence to Single or Continue.

If you selected Continue in step 4, use the

jog shuttle

and

SELECT

to set

Count to a value in the range of 2 to 128.

Use the

jog shuttle

and

SELECT

to select the Auto Naming method from OFF,

Numbering, and Date.

As necessary, enter the File Name and Comment according to the procedures

given in section 4.2.

Executing the Realtime Recording

Press the

START/STOP

key to start the waveform acquisition. Realtime

recording is executed.

While realtime recording is executing,

is displayed at the upper left corner of

the screen.

Aborting the Realtime Recording

Press the

START/STOP

key to stop the waveform acquisition. Realtime

recording is aborted.

Note

If you stop the waveform acquisition by pressing the START/STOP key, realtime recording is
aborted even if it is within the specified recording time.

Summary of Contents for 701210












































































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for 701210

Reviews:

YOKOGAWA 701210, User Manual, Page: 282 / 747

Search results

Summary of Contents for 701210

Reviews: