YOKOGAWA 701210 User Manual Download Page 279

Page: 279 / 747

7-13

IM 701210-05E

Acquisition and Display

Explanation

This function enables waveform acquisition in low-speed roll mode (main waveform)

along with high-speed waveforms (sub waveform) at a different sampling interval. It is

useful when capturing at high speeds abnormal phenomenon that occurs suddenly

during long-term observation (low-speed sampling). The sub waveform is saved

simultaneously when the main waveform is saved. Likewise, when the main waveform is

loaded, the sub waveform is also loaded. This function is valid when the acquisition

mode is set to normal, envelope, or box average.

Cannot tell how many burst waveforms occurred

When displayed using the zoom function

When displayed using the dual
capture function

Main waveform

Able to observe the occurrence of
five burst waveforms

Observe this phenomenon using the
zoom function (horizontal zoom) and
the dual capture function
(T/div: 100

s/div for both)

Sub waveform window

Event waveforms
Displays the time when the sub waveform was
acquired as an event waveform

Sub waveform acquired here

The dual capture function has the following two trigger modes.

• Auto Mode

For the main waveform, measurement is performed from the time sampling is started

until there is a request to end the sampling. The number of sub waveforms that can

be saved varies between the standard model and memory expansion models (/M1, /

M2, and /M3).

Standard model:

Up to 100

/M1 model:

Up to 250

/M2 and /M3 models:

Up to 500

If the maximum number of sub waveforms is exceeded, the oldest sub waveform is

deleted, and the newest waveforms are saved.

• Log Mode

For the main waveform, the waveform is acquired from the time sampling is started up

to the specified record length. For the sub waveform, up to 100 sets can be stored.

When this number is reached, the acquisition of sub waveforms stops.

Waveform Acquisition Condition of the Dual Capture Function

Waveforms can be acquired when all of the following conditions are met.

• When the T/div setting of the main waveform is from 100 ms/div to 3 days/div

• When the sample rate of the main waveform is less than or equal to 100 kS/s

• When the sample rate of the main waveform is less than the sample rate of the sub

waveform

Applicable Channels

The applicable channels are all channels that are identified for both main waveform and

sub waveform (However, when the record length is greater than or equal to 2.5 MW on

the standard model, 10 MW on the M1 option model, 25 MW on the M2 option model,

and 50 MW on the M3 option model, the applicable channels are those that are turned

ON). DSP channels are also applicable.

7.6 Using the Dual Capture Function

Summary of Contents for 701210












































































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for 701210

Reviews:

YOKOGAWA 701210, User Manual, Page: 279 / 747

Search results

Summary of Contents for 701210

Reviews: