YOKOGAWA 701210 User Manual Download Page 276

Page: 276 / 747

7-10

IM 701210-05E

7.5

Acquiring Data Using the Sequential Store
Function (Single (N) Mode)

<For a description of this function, refer to page 2-33.>

Procedure

MEASURE CURSOR

RESET

SELECT

ALL CH

MODE

POSITION

SIMPLE/ENHANCED

ACQ

START/STOP

SETUP

DISPLAY

ZOOM

DUAL

CAPTURE

HISTORY

MATH

DELAY

MANUAL TRIG

V/DIV

TIME/DIV

TRIGGER

TRIG D

VERTICAL

HORIZONTAL

CAL

X-Y

SEARCH

DSP 1

DSP 2

ENTER

DSP 6

DSP 5

LOGIC A

LOGIC B

EVENT

DSP 3

DSP 4

EXP

GO/NO-GO

ACTION

FILE

SHIFT

Press

MODE

Press the

Single(N)

soft key.

Use the

jog shuttle

and

SELECT

to set Single(N) Count.

Explanation

By setting the trigger mode to Single(N), the sequential store function can be used.

Acquisition Count

Set the acquisition count in the range from 1 to 2000.

However, the selectable acquisition count varies depending on the selected record

length and acquisition mode.

For details, see appendix 1, “Relationship between the Time Axis Setting, Sample Rate

and Record Length.”

Displaying Waveforms

You can recall waveforms from memory in the same fashion as for the history memory

function.

For details, see section 11.1, “Displaying History Waveforms.”

Notes When Using Sequential Store

• If you stop waveform acquisition by pressing the START/STOP key, the sequential

store operation also stops. Sequential store restarts from the beginning when

acquisition resumes.

Summary of Contents for 701210












































































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for 701210

Reviews:

YOKOGAWA 701210, User Manual, Page: 276 / 747

Search results

Summary of Contents for 701210

Reviews: