YOKOGAWA 701210 User Manual Download Page 219

Page: 219 / 747

6-1

IM 701210-05E

Triggering

Chapter 6

Triggering

6.1

Setting the Trigger Mode

<For a description of this function, refer to page 2-27.>

Procedure

MEASURE CURSOR

RESET

SELECT

ALL CH

MODE

POSITION

SIMPLE/ENHANCED

ACQ

START/STOP

SETUP

DISPLAY

ZOOM

DUAL

CAPTURE

HISTORY

MATH

DELAY

MANUAL TRIG

V/DIV

TIME/DIV

TRIGGER

TRIG D

VERTICAL

HORIZONTAL

CAL

X-Y

SEARCH

DSP 1

DSP 2

ENTER

DSP 6

DSP 5

LOGIC A

LOGIC B

EVENT

DSP 3

DSP 4

EXP

GO/NO-GO

ACTION

FILE

SHIFT

Press

MODE

Press the soft key corresponding to the desired mode to set the trigger mode.

If you select Single(N), turn the

jog shuttle

to set Single(N) Count (the number

of times to acquire the waveform).

Explanation

Auto Mode

If the trigger condition is met within the 50-ms timeout period, the waveform is updated

on each trigger occurrence. If the trigger condition is not met after the timeout period

elapses, the waveform is automatically updated. If the time axis setting is in the range in

which the display mode is set to roll mode, the display is set to roll mode.

However, triggering operates in normal mode when using simple trigger with the trigger

source set to Time, even if auto mode is specified.

Auto Level Mode

Within the timeout period (approximately 1 s), the waveforms are displayed in the same

fashion as in the auto mode. If a trigger does not occur within the timeout period

(approximately 1 s), the center value of the amplitude of the trigger source is detected,

the trigger level is automatically changed to the center value, and the trigger is generated

to update the displayed waveform. The auto-level mode is valid only if the trigger is a

simple trigger and the trigger source is between CH1 and CH16. For all other cases, the

operation is the same as the auto mode.

If the time axis setting is in the range in which the display mode is set to roll mode, the

display is set to roll mode.

Summary of Contents for 701210












































































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for 701210

Reviews:

YOKOGAWA 701210, User Manual, Page: 219 / 747

Search results

Summary of Contents for 701210

Reviews: