manualshive.com logo in svg

YOKOGAWA 701210, User Manual, Page: 191 / 747

Share
Download
YOKOGAWA 701210 User Manual Download Page 191

5-31

IM 701210-05E

Horizontal and Vertical Axes

5

5.17 Setting the Strain Measurement

<For a description of this function, refer to page 2-14.>

Procedure

MEASURE CURSOR

RESET

SELECT

CH

ALL  CH

MODE

POSITION

SIMPLE/ENHANCED

ACQ

START/STOP

SETUP

DISPLAY

ZOOM

DUAL

CAPTURE

HISTORY

MATH

 1

CH

 2

CH

 3

CH

 4

CH

 5

CH

 6

CH

 7

CH

 8

CH

 9

CH

 10

CH

 11

CH

 12

CH

 13

CH

 14

CH

 15

CH

 16

DELAY

MANUAL  TRIG

V/DIV

TIME/DIV

TRIGGER

TRIG  D

VERTICAL

HORIZONTAL

CAL

X-Y

SEARCH

7

DSP 1

8

9

DSP 2

6

5

4

1

0

2

3

ENTER

m

DSP 6

DSP 5

LOGIC  A

LOGIC  B

EVENT

DSP 3

DSP 4

EXP

GO/NO-GO

ACTION

FILE

SHIFT

1.

Press a key from 

CH1 

to 

CH16 

keys to select the desired channel (select a

channel with the Strain Module (701270 (STRAIN_NDIS) or 701271

(STRAIN_DSUB)) installed).

Selecting the Measurement Range

2.

Press the 

Range Unit 

soft key, and then press the 

µ

STR

 (the unit of strain) or

mV/V 

(the unit of the output value of the strain gauge transducer) soft key.

Note

Be sure to execute balancing when you change the measurement range.

• When 

µ

STR Is Selected

3.

Use the 

jog shuttle 

to select the Range from 500 

µ

STR to 20000 

µ

STR.

• When mV/V Is Selected

3.

Use the 

jog shuttle 

to select the Range from 0.25 mV/V to 10 mV/V.

Note

If the range unit is set to mV/V, a numeric value is displayed at the right side of the range
display.  This value is the maximum input at the current bridge voltage converted to volts.  It
indicates the maximum input voltage at the selected range.

Setting the Display Range

4.

Press the 

Upper/Lower 

soft key to set the jog shuttle control to Upper.

5.

Turn the 

jog shuttle 

to set the upper limit.

6.

Likewise, set Lower.

Note

Pressing RESET sets the upper and lower limits to the maximum and minimum values of the
measurement range.

When Range 
Unit is 

µ

STR

When Range 
Unit is mV/V

Summary of Contents for 701210












































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments