YOKOGAWA 701210 User Manual Download Page 180

Page: 180 / 747

5-20

IM 701210-05E

• P1–P2

Specify arbitrary scale values (P1:Y and P2:Y) for the measured values of two

arbitrary points (P1:X and P2:X). The scale conversion equation (y = ax + b) is

derived from these four values.

• Range of measured values (P1:X, P2:X): Same as the measurement range.

• Range of scale values (P1:Y, P2:Y):

–1.0000E+25 to +1.0000E+25

• Initial setting of scale values:

P1:X=+0.0000E+00, P1:Y=+0.0000E+00

P2:X=+1.0000E+00, P2:Y=+1.0000E+00

Measurement range

P1:X

P2:X

P1:Y

P2:Y

y=ax+b

Measured value

Scale value

Setting AX+B

• Setting Scaling Coefficient A and Offset Value B

Selectable range of A and B:

–9.9999E+30 to +9.9999E+30

Initial setting of A:

+1.0000E+00

Initial setting of B:

+0.0000E+00

Setting P1–P2

• Reading Measured Values: Get Measure

Regardless of whether the waveform acquisition is started or stopped, the current

value (value indicated by the level indicator) can be read into P1:X or P2:X.

Setting the Unit

Alphanumeric characters that can be entered: Up to 4 characters

Display Type

When measuring voltage on the voltage module or strain on the strain module, select the

display type for the linear scaling result from the two choices below.

Exponent:

Exponential display.

Floating:

Decimal display. Use Decimal Number to select the number of digits to the

right of the decimal from Auto, 0 to 3. Use SubUnit to select the sub unit

from Auto, p, n,

, m, None, k, M, G, and T.

• Decimal Number:

When a setting between 0 and 3 is selected, the selected

number of digits is displayed to the right of the decimal point.

When Auto is selected, the value is displayed using 5 digits

total (example: 1.0000 and 250.00). The initial setting is Auto.

• SubUnit:

If a setting other than Auto is selected, the value is displayed

using the specified sub unit. If Auto is selected, the most

suitable unit for the value is automatically set. The initial setting

is Auto. If the value cannot be displayed using a decimal value,

exponential display is enabled.

Displaying the Scale Value

The linearly scaled values of the upper and lower limits of the vertical axis of each

channel can be displayed. For details, see section 8.9.

5.11 Using the Linear Scaling Function (AX+B, P1-P2)

Summary of Contents for 701210












































































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for 701210

Reviews:

YOKOGAWA 701210, User Manual, Page: 180 / 747

Search results

Summary of Contents for 701210

Reviews: