manualshive.com logo in svg

YOKOGAWA 701210, User Manual, Page: 136 / 747

Share
Download
YOKOGAWA 701210 User Manual Download Page 136

3-33

IM 701210-05E

  Making Preparations for Measurements

3

3.14 Connecting the Earphone Microphone with a

PUSH Switch and Connecting the Speaker

The optional earphone microphone with a PUSH switch (701951) must be connected to

use the voice memo function (see section 7.9) and voice comment function (section

13.19).  The recorded voice memo and voice comment can be played through an

external speaker by using an optional speaker cable (701952) that is sold separately.

Connecting the Earphone Microphone with a PUSH Switch (701951)

Insert the 

φ

2.5 plug of the earphone microphone with a PUSH switch to the VOICE IN/

OUT/SW terminal of the DL750/DL750P left side panel.

REC LEVEL knob
Adjusts the recording level of voice 
memos and voice comments.  
Set to the center position (clicks in 
place) for an adequate recording level.

VOLUME knob
Adjusts the play volume of voice 
memos and voice comments.  Set to 
the center position (clicks in place) 
for an adequate play volume.

VOICE IN/OUT/SW terminal
Connect the earphone microphone 
with a PUSH switch here.

PUSH switch

Microphone

Earphone

Cord clip

Higher

Lower

Higher

Lower

Specifications of the Earphone Microphone with a PUSH Switch

Dynamic Inner Earphone

Input impedance:

32 

Ω

Frequency range:

100 to 20 kHz

Maximum input:

40 mW

Electric Condenser Microphone

Output impedance:

1.6 k

Ω

Frequency characteristics:

100 to 10 kHz

Directional characteristics:

Omnidirectional

Code:

1.2 m, 

φ

2.5, with 4-pin plug

Weight:

Approx. 16 g

Earphone Microphone Jack Input/Output

Jack:

4-pin jack

Microphone input:

Electric condenser microphone, input impedance of approx. 5 k

Ω

Earphone output:

Dynamic, impedance of 32 

Ω

Switch input:

10-k

Ω

 pull-up (3.3 V)

Note

•

The specifications above apply to the optional earphone microphone with a PUSH switch
(701951) that is sold separately.  Operation of other earphone microphones are not
guaranteed.

•

There is no protection circuit, because it is a dedicated input.  Be sure to use the
dedicated earphone microphone by YOKOGAWA.

Summary of Contents for 701210












































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments