manualshive.com logo in svg

YOKOGAWA 701210, User Manual, Page: 110 / 747

Share
Download
YOKOGAWA 701210 User Manual Download Page 110

3-7

IM 701210-05E

  Making Preparations for Measurements

3

Removal

1.

Check that the power switch is OFF.

2.

Loosen the screws holding the input module in place.

3.

Holding the handles on the top and bottom of the input module, pull out the

module.

LEDs on the Frequency Module

On the front panel of the frequency module (701280 (FREQ)) are LEDs for each

channel.  These LEDs allow you to check the input condition of the pulse.

ACT
OVER

ACT
OVER

701280(FREQ)

LED
Illuminated in green: When pulse is applied
Illuminated in red:  When the input voltage 
 

 

level is over range.

Off: When pulse is not applied

Note

•

The LEDs on the frequency module illuminates in green when pulse is applied and red
when the input voltage level is over range.  It is independent of the start/stop condition of
waveform acquisition of the DL750/DL750P.

•

If the frequency module preset (see section 5.19) is set to “EM Pickup (electromagnetic
pickup),” the LED does not illuminate in red even when the input voltage level is over
range.

3.3 Installing Input Modules

Summary of Contents for 701210












































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments