manualshive.com logo in svg

YOKOGAWA 701210, User Manual, Page: 106 / 747

Share
Download
YOKOGAWA 701210 User Manual Download Page 106

3-3

IM 701210-05E

  Making Preparations for Measurements

3

3.2

Installing the Instrument

Installation Conditions

Install the instrument in a place that meets the following conditions.

Flat, Even Surface

Set the instrument in the proper direction (see page 3-4) and in a level and stable place.

Note that the instrument can be tilted on the stand if the instrument is set with the rear panel

facing down.  If placed in an uneven or unstable place, printing quality may deteriorate.

Well-Ventilated Location

Vent holes are situated on the bottom side of the instrument.  In addition, vent holes for

the cooling fans are also situated in the left side and the bottom.  To prevent internal

overheating, allow for enough space around the instrument (see the figure below) and do

not block the vent and inlet holes.

10 cm or more

10 cm or 
more

10 cm or 
more

5 cm or 
more

5 cm or 
more

DL750

DL750P

When connecting the various cables or when opening or closing the built-in printer cover,

take extra space in addition to the space indicated above for the operation.

Ambient Temperature and Humidity

Ambient temperature:

5 to 40

°

C

Ambient humidity:

20 to 85% RH (when not using the printer)

}

 No condensation

35 to 85% RH (when using the printer)

Note

•

To ensure high measurement accuracy, operate the instrument in the 23 

±

 5

°

C

temperature range and 55 

±

 10% RH.

•

Condensation may occur if the instrument is moved to another place where the ambient
temperature is higher, or if the temperature changes rapidly.  In such cases, allow the
instrument adjust to the new environment for at least an hour before using the instrument.

Summary of Contents for 701210












































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments